Search published articles


Showing 3 results for Dilation


Volume 3, Issue 2 (4-2010)
Abstract

(Paper pages 735-756) Shear behavior of sand-gravel mixtures is an important issue in geotechnical engineering due to extensive use in earth dams, borrow materials and slope stability problems of natural or man made slopes. Experimental study of behavior of this type of material is usually difficult due to problems associated with use of large testing apparatus or large specimens. Several researchers have proposed methods for the test of these materials by removing larger fraction of them and testing finer matrix. In this research, a regular set of large direct shear tests with a 300*300*160 mm shear box performed to determine shear strength and dilation characteristics of sand-gravel mixtures in high gravel contents. Bad graded fine sand was used besides uniform gravel grains with maximum grain size of 12.5 mm as testing materials. The tests conducted on mixtures prepared in four gravel contents of 70, 80, 90 and 100 percents. Samples constructed in three relative densities of 35, 60 and 85% and tested by different surcharge pressures of 100, 200 and 300 kPa. Experiments conducted on completely dry samples in consolidated drained condition. Shear strength behavior of mixtures was investigated and it was concluded that both shear strength and friction angle increases with gravel content, relative density and surcharge pressure. However, dilation increases by increase in gravel content and relative density and reduces with increase in surcharge pressure. Results were compared with previous experiments on mixtures with less gravel contents and it was observed that in little gravel contents the behavior is controlled by the both sandy matrix and gravel grains. However, as gravel content increases from floating limit, the behavior is mainly controlled by gravelly part of mixture and sand fraction has little effects on its behavior.
Gholamhosein Tavakoli Mehrjard, Fariba Motarjemi,
Volume 12, Issue 2 (10-2018)
Abstract

Introduction
The general failure mechanism of soil element in geotechnical structures is shear failure under static and dynamic loads. Therefore, assessment of soils’ shear strength parameters is very crucial in the performance of geotechnical structures, especially in slope stability. Tavakoli Mehrjardi et al. (2016) showed that by increasing soil grain size in unreinforced soil masses, bearing capacity of foundation increases due to increasing shear strength parameters of soil mass. Furthermore, Tavakoli Mehrjardi and Khazaei (2017) found out that generally, for all reinforced and unreinforced conditions, cyclic bearing capacity was enhanced by increasing the medium grains size of backfills. Taking into account the deficiency of studies on the shear characteristics of soil, a series of large direct shear test have been carried out to investigate and to compare effects of the soil’s physical properties such as aggregate size and relative density, besides of normal stress, on the shear characteristics of the backfills.
Material and Test Program
In this study, three types of uniformly graded soils as fill materials with the medium grain size (D50) of 3, 6 and 12 mm were considered. These soils are classified as SP and GP in the Unified Soil Classification System. It should be mentioned that these materials can be used in railroad as ballast and in retaining walls as fill materials. The current study aims to investigate strength characteristics of the backfills, influenced by different parameters such as relative density of the fill materials, normal stress on the shear plane and aggregate size of the fill materials. To cover all the matters, 18 large-scale direct shear tests have been scheduled. These tests encompass two relative densities of fill materials (50% and 70% which represent medium dense and dense backfill, respectively), three aggregate sizes of fill materials (3, 6 and 12 mm- selected based on the scaling criteria on size of shear box) and three normal stresses (100, 200 and 300 kPa- these values cover rather low to high vertical stress in a soil element of common geotechnical projects) have been examined. It should be mentioned that, prior to shearing, the normal stress was applied to the specimens for a period of 1 h, in order to stabilize the soil particles from any possible creep. As all materials used in this research are of coarse-grained type and the experiments were performed under dry conditions, the displacement rate of 0.5 mm/min was selected. During the tests, the applied normal stress, displacement of the lower box, shear force mobilized at the interface and vertical displacements of the cap were continuously recorded.
Results and discussion
The curves of shear stress as a function of shear displacement and also shear displacement-vertical displacement for samples show that shear stress dropped down to a specific amount of residual shear strength after reaching maximum amount of shear stress . It was observed that increasing the particle size and relative density of the fill materials mostly fortify interlocking of the grains which in turn, resulted in increasing the tendency to expansion through the shear plane. On the other hand, the initial compression has decreased and dilation was started from a smaller shear displacement. This may be interpreted that as the soil particles size increases, more expansion is required to reach the maximum shear strength. Moreover, comparing the observed behavior, it is found out that unlike the effect of grain size and density, increasing the normal stress caused the materials to be more compressed, resulted in reducing expansion and increasing the initial compression of the soil mass. This conceivably means that increasing normal stress, transferred on shear plane, can change the failure mechanism of materials, from dilatancy failure to bulging failure under shearing. From the results, it was found out that increasing medium grains size of soil from 3 mm to 12 mm ended to improvement in the maximum friction angle at relative density 50 and 70% by the value up to 4.4 and 5.8 degree, respectively. In fact, due to increasing grain size, the grains interlocking have been fortified. In order to have a comparison, the maximum dilation angles of all fill materials, mobilized at the shear plane, have been derived. Accordingly, the maximum dilation angle was increased with the increment of the fill grains size and relative density of the material. Nevertheless, by considering variation of peak dilation angle with normal stress, it is found out that the normal stress had a negative influence on the advancement of interface’s dilation angle. These findings can be directly interpreted by considering the compression/expansion of the materials during the increment of shear displacements.
Conclusion
The current study, consists of 18 large-scale direct shear tests, aims to investigate shear characteristics of soil which influenced by different parameters such as relative density of the fill materials, normal stress at the shear plane and aggregate size of the fill materials. Eventually, the following conclusions are presented:
  • Increasing relative density, soil particle size and normal stress have beneficial effect in shear strength improvement. But, the mechanisms of each parameter in this enhancement is different.
  • The dilation rate of shear interfaces directly complies with changes in the ratio of applied shear stress to vertical stress. So, the maximum dilation angle and the maximum ratio  mobilized at the shear plane have occurred around the same shear displacement.
  • Maximum values of friction and dilation angels have been occurred around the same shear displacement. Moreover, compaction effort leads to increase the required shear displacements to approach the maximum shear characteristics.

Mr Vahid Yousefpour, Mr Amir Hamidi, Mr Ali Ghanbari,
Volume 13, Issue 5 (12-2019)
Abstract

Sandy soils usually contain different amounts of fines like silt and clay, causing some changes to their shear strength and dilation characteristics. Bolton [1] conducted  some experiments on the different sands and suggested a relation between the parameters of the soil shear strength. In this paper, some experiments were performed on fine contained sand and the extended Bolton's relation was has been proposed. In this paper, shear strength and dilation behavior of a pure sand mixed with different amounts of silt or clay fines were studied using direct shear test device (100*100*30 mm), and a total of 96 tests were carried out. The samples were prepared separately using clay and silt contents of 0, 10, 20 and 30% in different relative densities of 70, 80, 90 and 100%. They were tested under three surcharge pressures of 90, 120 and 150 kPa, under particle crushing threshold. Variations in shear strength, maximum friction angle, critical state friction angle and cohesion, as well as dilation angle were investigated by increasing in the mentioned amounts. The results demonstrate that shear strength, dilation angle, maximum friction angle decreased by clay content increase, however, they increase with increase in silt content. In addition, a new form of the Bolton's relation for fine contained sandy soils was presented.

Page 1 from 1     

© 2024 CC BY-NC 4.0 | Journal of Engineering Geology

Designed & Developed by : Yektaweb