Search published articles


Showing 2 results for Asmari Formation

Akbar Cheshomi, Ebrahim Ahamadi Sheshde,
Volume 6, Issue 1 (11-2012)
Abstract

Determination of uniaxial compressive strength (UCS) of intact rock is an important mechanical parameter required for many engineering projects. In some engineering projects, for example, well drilling has been accomplished for petroleum. The requirement of deep well to take samples to obtain rock core sample for determination of UCS is a difficult task. On the other hand, determination of this parameter is essential in order to analyze well wall stability and well development program. Therefore, the idea of using drilling cuttings is proposed for determination of UCS. In this paper, in order to develop relationship between UCS and single compressive strength (SCS) 7 block sample of microcrystalline limestone from Asmari formation were used. Then UCS test was performed and uniaxial compressive strength was determined. Next, these samples were crushed and 420 single particles were prepared. Then SCS for each particle was determined. Since the shape of particles affects particle strength, shape of particles was modified.  The total particles used for determination of SCS were spherical. In order to study the effect size of particle, particles with diameters 2, 3 and 4 millimeters were prepared and the SCS for each particle has been determined. With the increase of diameter of particles, the SCS has been increased too. In order to eliminate the effect of size of particles, it is defined variable size and strength and proposed chart between them. Coefficient of correlation between SCS and UCS is more than 0.91 which indicates a high correlation between them.
Ako Daraei, Shokrollah Zare,
Volume 12, Issue 4 (12-2018)
Abstract

Introduction
It is very important to have knowledge on the rock deformation modulus when designing geotechnical ‎structures and modeling oil reservoirs. In general, there are two destructive or static and non-‎destructive or dynamic methods for determining the rock deformation modulus, but considering the ‎time and cost of destructive methods proportionate to the depth, it is more common to make use of ‎non-destructive approaches. The outcrops of Asmari Formation are widely spread in the west and ‎southwest of Iran, and many engineering projects have been constructed or are being studied ‎on this formation. Therefore, it is of great importance to study on the geomechanical characteristics of this ‎formation. Presentation of empirical relations regarding the relationship between static and dynamic ‎moduli, with respect to the studies carried out in other parts of the world and the dispersion and ‎independence of studies done on Asmari Formation due to its large extent on one hand and the ‎importance of this formation in terms of oil and development civil projects on the other hand, necessitate ‎presenting a comprehensive criterion resulted from all studies carried out on Asmari Formation which ‎can express the relationship between the static and dynamic moduli. This paper represents the ‎relationship between the dynamic and static moduli of the site using the moduli obtained by the ‎down-hole geophysical method and the static moduli obtained by the intact rock test results of ‎Ghalajeh tunnel located in Asmari Formation in Ilam province. Then, a comprehensive relation is ‎presented to express the relationship between static and dynamic modulus by studying the previous ‎researches and criteria on this formation.
Material and methods
Two sets of tests were conducted to determine the relationship between static and dynamic moduli in the Ghalajeh tunnel. First, a uniaxial compression strength test was performed on 13 cores taken from three boreholes to compute the elasticity modulus in accordance with ISRM standard. Then, down-hole test was conducted on two boreholes such that to determine the dynamic modulus using compressive and shear wave velocities. Seismographic apparatus of ABEM RAS 24 as well as three-component down-hole geophones were utilized in order to plot the seismic profile. After the performing the tests, the dynamic modulus of deformation was calculated using the velocity of P-waves and the density of the host rock.
Discussion and Conclusions
By conducting in-situ static and dynamic laboratory tests on Ghalajeh Tunnel project and determining the values ​​of the static and dynamic deformation moduli, a relation was presented between them. Then, taking into consideration the previous models studied in Asmari Formation, a comprehensive criterion was presented for wider use in the mentioned formation. Given the root mean square error (RMSE) and variance account for (VAF), the values predicted using the proposed comprehensive model have acceptable accuracy. In the interim, the correction factor between dynamic and static moduli in Asmari Formation was between 0.8 and 2.4. The results show that, in general, the relationship between static and dynamic moduli is linear up to a certain range (static modulus of 100 MPa) and then it has a power trend./files/site1/files/124/4darai%DA%86%DA%A9%DB%8C%D8%AF%D9%87.pdf

Page 1 from 1     

© 2024 CC BY-NC 4.0 | Journal of Engineering Geology

Designed & Developed by : Yektaweb