Search published articles


Showing 3 results for Squeezing

H Sadeghi, S Mahdevari,
Volume 7, Issue 1 (8-2013)
Abstract

One of the major challenges in tunneling is the excavation in regions with high potential of squeezing and in the case of application of full face boring machines evaluation of the required thrust in these regions is inevitable. The Beheshtabad water conveyance tunnel with 65 km in length is considered for transferring one billion cubic meter of water annually to the central part of Iran.  According to geological investigation there is a high potential of squeezing in the 19th section of tunnel. In this article, the thrust evaluation methods are investigated and the required penetration force is calculated. Then the numerical procedure applicable to thrust evaluation in the 19th section is discussed and the results are analyzed.  In addition, the required thrust to overcome shield skin frictional resistance using Ramoni's method (2010) is computed and the outputs are compared to numerical ones. As a result of numerical simulation, in order to utilize double shield TBM for the sections of 29030-31600 km and 34900-37490 km, it is required to overcut 3 cm for the favorable geomechanical locations and 10 cm for the unfavorable geomechanical conditions. Decision on the application of full face boring machines in the section of 31600-34900 km could be made providing long term parameters of host rock were determined via performing additional in situ tests in the exploration gallery.  
Hadiseh Mansouri1, Rassoul Ajalloeian, Alireza Nadimi,
Volume 13, Issue 3 (11-2019)
Abstract

Introduction                               
Generally, in engineering geology physical and mechanical properties of rocks are investigated in macroscopic scale, and less attention is paid to investigate the texture and microstructure developing in rock during deformation. Salt rock, as a best example of ductile rocks, has attracted the attention of many researchers. Compared to silicate rocks, salt rock exhibits extensively ductile behavior at even low temperature and pressure. In micro-tectonics, salt is important, because of it is useful as an analogue material for understanding the microstructural processes and textural development in silicate rocks. Deformed salt rock can display microstructures developed in silicate rocks at high pressures and temperatures. Regarding the similarity between microstructures of salt rock and silicate rocks, investigation of microstructure and deformation mechanism in salt rock can be helpful in understanding the main cause of the squeezing phenomenon in tunnels.
One of the effective factors on squeezing phenomenon is the structures and microstructures of rock. Rock mass classifications that contain rock mass structures are used in the predicting methods. But, so far, no attention has been paid to the role of rock microstructure in predicting the squeezing phenomenon.
This study is aimed to identify deformation mechanisms occurring in microscopic scale in rocks and lead to tunnel convergent in large scale. To achieve this goal, the microstructures in a naturally deformed Late Pre-Cambrian to Early Cambrian Hormuz salt rock from the active Deh Kuyeh salt fountain in Fars province were investigated using Electron Backscatter Diffraction (EBSD).
Materials and Methods
Deh Kuyeh salt diapir was located at about 27 km NE of Lar city. Salt samples were taken from top of the east and west glaciers (S1 and S2) and from the middle part of diapiric stem (sample S3). Raw samples were first cut dry into slabs (approximately 3´2 ´1 cm). Thin sections were prepared following the procedure of Schleder and Urai (2005) and Urai et al. (1987).
Halite crystallographic orientation data were collected using a Zeiss SIGMAVP FEGSEM. EBSD patterns were collected using an accelerating voltage of 30 kV, beam current of ~ 100 nA and a working distance of about 30 mm. Oxford instruments AZTEC software was used for data acquisition. EBSD large step size (50 mm) mapping was used to examine the overall microstructure in each sample. EBSD data were processed using HKL Channel 5 software.
Results and Discussion
All samples showed relatively similar microstructures. Samples comprise a small number of large grains in a matrix of smaller grains. Most grains were irregular in shape with lobate boundaries and internal distortion. Microstructural study revealed that the ductile flow of the salt was accommodated by dislocation creep and dynamic recrystallization. Salt grains show lattice distortion and a prevalence of low-angle boundaries that are evidence for dislocation creep and recovery processes. Misorientation analysis suggests that (110) <110> and (111) <110> slip systems are responsible for crystal plastic deformation of salt grains. Schmid factor analysis showed that stresses acting on inclined directions lead to the maximum activity of these slip systems.
The observed microstructures in the salt are comparable with the microstructures presented for schist samples from Himalaya region. The rock along Himalaya main trusts also showed evidence of dislocation creep and development of crystallographic preferred orientation. Hence, this article suggests that the rock type and its microstructures are the most important factors in occurrence of tunnel convergent.
Conclusions
This article proposes that deformation mechanisms occurring in micro-scale control the rock behavior in large scale. All rocks can behave as a ductile material depending on the temperature and pressure. In intrinsically ductile rocks like salt rock, presence of many active slip systems facilitates rock deformation under lower pressures and temperatures than silicate rocks. High tectonic stresses in shear zones lead to development of a strong shape preferred orientation and crystal preferred orientation in rocks. These microstructures facilitate rock deformation under stresses exiting in tunnels. It can be said that rock type and tectonic history of the area play the most important role in occurrence of squeezing phenomenon. Other factors such as current stress system in the area control deformation speed in tunnel. It seems investigating microstructures of rocks from tunnel route before and after excavation can be effective in identifying places with high possibility of squeezing.
M.sc. Behrooz Margan, Dr. Davood Fereidooni,
Volume 18, Issue 1 (5-2024)
Abstract

In this research, various aspects of the rock burst phenomenon in the Haji-Abad tunnel site in the Hormozgan province have been discussed. Considering that the tunnel site is located in an active tectonized environment in terms of geological conditions and the depth of the tunnel in some parts reaches more than 100 to 253 m, and also considering the variety of rocks in the tunnel site, which are massive rocks with high strength up to broken fault zones, the importance of studying and investigating the phenomenon of rock burst is very important for the safety of the labor force and equipment and the stability of the underground space. For this purpose, the Haji-Abad tunnel site has been divided into ten units of engineering geological conditions using the BGD method, which includes eight units T1 to T8 and two crashed zones Tf1 and Tf2. Then, using common experimental and semi-experimental methods, the phenomenon of rock burst in the tunnel site has been evaluated. In the experimental procedure, Goel et al.'s criterion was used, according to which the rock burst phenomenon does not occur in any of the tunnel units. Using semi-empirical methods, including the criterion of linear elastic energy of the tunnel site units in the range of very low to moderate rock burst phenomena and using the tangential stress criterion, the site units in the medium to very high range and based on the stress criteria of these units in the moderate to high range and finally, using the fragility criterion, all site units are placed in the range of high rock burst.


Page 1 from 1     

© 2024 CC BY-NC 4.0 | Journal of Engineering Geology

Designed & Developed by : Yektaweb