Journal of Engineering Geology

---

This paper investigates response of triangular shell strip footings situated on the sandy slope. A series of reduced-scale plate load tests were conducted to cover different parameters including three shell footing types with different apex angles in addition to a flat footing, four different distances for strip footings from the crest of the slope namely “edge distance” and reinforcement status (unreinforced and geotextile-reinforced statuses). Bearing capacity of shell footings adjacent to crest of the slope, bearing capacity ratio, shell efficiency factor, influence of apex angle on settlement of footings and the mechanism of slope failure are discussed and evaluated. Also, empirical equations for determination of the maximum bearing capacity of triangular shell strip footings are suggested. As a whole, it has been observed that decrease of shell’s apex angle as good as increase of edge distance could significantly improve the bearing capacity. However, as the edge distance increases, the effect of apex angle on the bearing capacity got decreased. Also, it was found out that the beneficial effect of reinforcement on the bearing capacity decreased with increase of the edge distance. Furthermore, the efficiency of shell footings on bearing capacity was attenuated in reinforced slopes compared to the unreinforced status.

---

The use of piles, helical anchors and, in general, helical foundations has considerably increased in the last 30 years. The adoption of this technology in the international and domestic codes of each country, as well as in research and studies, and, finally, the publication of numerous books and papers in this area, and the existence of manufacturers’ products, committees, and contractors of this technology has contributed to its expansion and development. However, such methods have progressed at a very slow pace in many countries, especially in developing countries. This paper attempts to assess the global advancement of the helical foundations by reviewing 292 papers from 1990 to 2020 and comparing the related research findings. This will help clarify the issue and determine the scope of technological progress. On the other hand, collecting valuable papers in this area will make it easier for researchers to make further research. Subsequently, the characteristics of this technology are highlighted and the reasons for its lack of progress in the developing countries are addressed. For this purpose, a questionnaire is sent to researchers, developers, designers, and contractors of the geotechnical projects. The purpose of this questionnaire is to specify the type of existing projects, the soil type of project site, the degree of familiarity with the helical foundation technology, the reasons for not using this method and the solutions available to expand and develop this method. Finally, there are suggestions to develop this approach and the issues that need further research.

---

Introduction
Grouting is one of the most widely used methods of soils improvement in which pressurized grout penetrates in the voids, of the soil. In the grouting method, in addition to reducing the permeability, shear strength and stiffness of the soil increase significantly. However, application of this method in projects such as dam construction and soil improvement requires the use of a large volume of grouting materials in order to satisfy the design criteria. In more recent years, due to the economic and environmental issues, in the case of cement-based grouts, replacing the whole or a portion of Portland cement with other materials has been experimentally investigated. A special type of kaolinite clay called metakaolin has recently been used in concrete, which has yielded interesting results. However, few studies has been conducted on the use of metakaolin in cement-based grouts. Such that, its effect on the mechanical behavior of the grouted soil are not well understood. Accordingly, in the present study, the mechanical behavior of a type of sandy soil grouted with different combinations of Portland cement and metakaolin was experimentally investigated in laboratory scale.
Material and methods
Different materials used in the present study including sand, cement, metakaolin, bentonite and water were selected based on the standard criteria and with the aim of better interpreting the test  result and their differences due to considered influencing factors. Sand was obtained from Malayer Shushab river bed. According to the Unified Soil Classification System (USCS), it is classified as SP. Ordinary Portland cement was used in this study regarding to its widespread application in the practical works. The metakolin is classified as class N pozzolan according to the ASTM C618. Another constituent material of grout is bentonite which is produced by Iran Barit factory as sodium-calcium bentonite. Its liquid limit and plastic index are 296 and 262 percent, respectively. The water used to prepare the grouts was provided from Hamedan drinking water, which according to ASTM C94 has the required quality for grouting operations in laboratory.
The device for grouting specimens was developed at the Soil Mechanics Laboratory of Bu-Ali Sina University during the present study. It equipped with grouting pressure control system and tool for keeping grout in homogeneous conditions during the grouting operation into specimen. The samples were prepared with 0, 5, 10, 15, 20 and 25 percent substitution of cement with metakaolin. Curing time of grouted samples was considered as14 and 28 days.
In order to investigate the factor affecting stress-strain behavior of the grouted sand, the samples were sheared using advanced triaxial apparatus. After passing considered curing time, the samples were sheared considering three levels of confining pressures of 50, 100 and 200 kPa and by applying axial strain rate of 1 mm per minute. For each test, the maximum deviator stress and its corresponding axial strain were recorded. In addition, for studying post peak behavior of grouted soil, for every one of tests, average ratio of deviator stress to the axial strain as softening modulus, was calculated from the deviator stress-axial strain curves.  The moisture content of the samples was also measured according to ASTM D2216 at the end of tests. In the following, the role of different factors influencing stress-stain behavior of grouted sand including; confining pressure, ratio of water to the mix of cement and metakaolin, percentage of metakaolin, curing time and moisture content were investigated.
Results and discussion
Figure 1 shows the effect of metakaolin as alternative of a portion of cement on maximum confined compressive strength and its corresponding axial strain.
For the samples confined by pressure of 50 kPa the maximum confined compressive strength is almost constant by replacing cement with metakaolin up to 10%. However, the amount of axial strain corresponding to the maximum compressive strength of the specimens increases by 6% (Figure 2). For 25% replacement, the maximum confined compressive strength of the samples decreases by 17% compared to the initial state (pure cement). In contrast, the axial strain value related to peak state of most samples has been increased by 4% in comparison to the initial state.
 
In the case of confining pressure of 100 kPa, by replacing up to 10%, the mean confined compressive strength of the specimens was almost constant. However, the amount of axial strain corresponding to the peak state of the specimens has been increased by a maximum value of 18%. For 20% replacement percentage the compressive strength of the specimens has been decreased by about 15% compared to the initial state. However, in the range of 20 to 25 percent, the reduction process has slowed down, which can be due to various factors such as the effects of sample densification during further increase of metakaolin. According to Figure 1, it can be seen that in the range of 20 to 25% substitution, the amount of strain at failure state increased by an average of 40%, which indicates that the sample is more deformable.
In the case of confining stress of 200 kPa, by replacing 10% of the cement with metakaolin, maximum confined compressive strength and its corresponding axial strain, has been increased by approximately 5 and 14%, respectively. With increasing cement substitution up to 25%, the resistance of the specimens decreased by 8% compared to the result of sample grouted with pure cement. Although, axial strain at peak state has been increased by 28%. From the Figure 1, it is obvious that increasing in confining pressure yeilds a considerable increase in the maximum compressive strength of grouted soil. Besides, post peak behavior of grouted soil is also affected significantly by confining pressure. Such that an increase in confining pressure leads to decrease in softening modulus. On the other word, grouted soil displays a more deformable behavior. It should be noted that these aspects of grouted sand cannot be described by unconfined test. However compressive strength of the grouted soils in the majority of case, has been evaluated based on the unconfined test results. 
Conclusion
The aim of this study was to investigate, in laboratory scale, the mechanical behavior of sand grouted with cement-based grout and considering different percentage of metakaolin as an alternative for a portion of cement. The soil samples were grouted using a specific device developed during present study. After passing curing time the samples were sheared using triaxial apparatus by considering three levels of confining pressures. The main findings of this experimental research are as follows:
- Replacing 10% of cement with metakaolin, increases deformability of grouted soil, without reducing compressive strength. Deformability of grouted soil increases with adding more percentage of metakaolin however, in this case compressive strength decreases.
- By increasing confining pressures, more values of metakaolin can be used instead of cement in the grout.
- Increasing confining pressure, increases compressive strength, increases deformability and deceases softening modulus at post peak behavior.
- Shear strength parameters of grouted sand is affected by adding metakaolin into the grout. Increasing the percentage of metakaolin results in small changes in the internal friction angle of the grouted sand, however, the amount of cohesion decreases.

---

Introduction
Landslides have an effective role in the destruction of freeways and railroads, which have been caused to many human and financial losses. Understanding this phenomenon and its effective factors can be important in planning for development projects and away from landslide prone areas. Based on extensive field in the Qazvin-Rasht freeway that the authors carried out in various researches in 2014-2017, it was found that the freeway was threatened by the type of instabilities due to variety of lithologies  and tectonic structures exploitation phase and needs to be stabilized. The purpose of this study is to determine of the distribution of landslides in different types of lithologicalunits of the Qazvin-Rasht freewaythat shows the role of geology and differences in geotechnical characteristics and tectonic structures in the creation and distribution of landslides on the road.The role of geology on the difference in geotechnical properties and tectonic structures in the creation and distribution in the road. Geological engineering properties and appropriate stabilization methods is the other goals of this study.
Material and Methods
In the study, the locations and the type of landslides are distinguished and the information were plotted on geological map. Then by the ARC GIS 10.2 program, and the use of area density method, the percentage of landslide events in each geological formation was identified. In order to study the role of lithology (type of rock, texture, mineralogy, weathering, alteration and erosion), sampling were carried out from rocks of Karaj formation, Shemshak formation, Cretaceous orbitalolina limestone and Fajan conglomerate. Geotechnical characteristics of the samples were determined by performing laboratory tests such as dry weight, porosity, uni-axial compressive strength according to ISRM standard (1979). For determining the role of tectonic structures (number of joints, dip and dip direction, length (m), spacing (cm), filling percentage, opening (mm), roughness, weathering, water, friction angle) were performed. Then, the results obtained from relative density and frequency were matched with the geological, geotechnical characteristics and tectonic structures of each formation.
Results
In order to separate different types of landslides on various kinds of rocks, area density and frequencyof  landslides were determined by Eqs 1 and 2. Graph of frequency and area density are presented in Fig. 6 and Table 2, respectively. As can be seen in this figure and table, in Karaj formation, the percentage of rock fall, toppling, avalanche, scree slope and combined slip are the highest. In the rocks belonging to the Shemshak formation, the susceptibility of the debris flow and landslides has been increased. In Fajan conglomerates and limestones of the Ziarat and Cretaceous formations, the rockfalls is more formed.
where L_I: area density, A_L:  area of landslides in each lithological unit, A_T: area of landslides in total area.
where L_F: frequency of landslide, N_L:  number of landslides in each lithological unit, N_T: number of landslides in total area.
Conclusion
Result showed that despite significant heterogeneity in lithology, geotechnics, engineering geology and tectonic structures, there are similarities between the types and distribution of landslides. Four of the identified landslides consist of rock fall, toppling, avalanche in the resistant and medium strength rocks such as andesite, trachy-andesite and basalts of Karaj formation, Cretaceous orbitalolina limestone and Fajan conglomerate with regard to the dominant direction of the joints in relation to the slope, the shear strength of the joints and their weathering, falling and scree slope in thesiliceous zone and composite landslide in the argilite-alounite zone due to the high alteration and groundwater level and water retention by the presence of clay minerals, landslide in the sequence of loose and resistant rocks, debris flow and landslides in the soils of Shemshak formation due to the lepidoblastic texture of the slate and their high erosion potential due to the weather climate along the Manjil-Rudbar freeway../files/site1/files/151/4.pdf

---

Introduction
Stone column installation method is one of the popular methods of ground improvement. Several studies have been performed to investigate the behavior of stone columns under vertical loads. However, limited research, mostly focused on numerical investigations, has been performed to evaluate the shear strength of soil reinforced with stone column. The stress concentration ratio (n) is one of the important parameters that uses in soil improvement by stone column method. Stress concentration ratio is the ratio of the stress carried by stone column to that carried by the surrounding soil. In this paper, the results of a laboratory study were used to examine the changes in the stress concentration ratio when normal and shear stress applied. Direct shear tests were carried out on specimens of sand bed material, stone column material and sand bed reinforced with stone column, using a direct shear device with in-plane dimensions of 305*305 mm and height of 152.4 mm. Experiments were performed under normal stresses of 55, 77 and 100 kPa. In this study, three different area replacement ratios (8.4%, 12%, 16.4%), and three different stone column arrangements (single, square and triangular) were considered for investigation. Loose sand and crushed gravel were used to make the bed and stone columns, respectively. In this study, the equivalent shear strength and equivalent shear parameters measured from experiments were also compared with those predicted by analytical relationships at stress concentration value of 1 and stress concentration value obtained from experiments.
Material Properties
Fine-grained sand with particle size ranging from 0.425 to 1.18 mm was used to prepare loose sand bed, and crushed gravel with particle size ranging from 2 to 8 mm was used as stone column material. The sand material used as bed material had a unit weight of 16 kN/m³ and a relative density of 32.5%, and the crushed stone material used in stone columns had a unit weight of 16.5 kN/m³ and a relative density of 80%. The required standard tests were performed to obtain the mechanical parameters of bed material and stone column material. As the diameters of model scale stone columns were smaller than the diameters of stone columns installed in the field, the particle dimensions of stone column material were reduced by an appropriate scale factor to allow an accurate simulation of stone columns behavior.
Testing Procedure
In this study, large direct shear device was used to evaluate the shear strength and equivalent shear strength parameters of loose sand bed reinforced with stone column. Experiments were performed under normal stresses of 55, 75 and 100 kPa. Two class C load cells with capacity of 2 tons were used to measure and record vertical forces and the developed shear forces during the experiments, and a Linear Variable Differential Transformer (LVDT) was used to measure horizontal displacement. The main objectives of this study was to calculate the stress concentration ratio of stone columns in different arrangement. Stress concentration ratio is the ratio of the stress carried by stone column to that carried by the surrounding soil, and can be calculated using Equation 1. For this purpose, the direct shear device was modified. Two miniature load cells with capacity of 5 kN were employed. The load cells were mounted on the rigid loading plate with dimensions of 305*305 mm² and thickness of 30 mm, as shown in Figure 1, All achieved data from the experiments including data on vertical forces, shear forces and horizontal displacements were collected and recorded using a data logger, and an especial software was used to transfer data between the computer and the direct shear device. All specimens were sheared under a horizontal displacement rate of 1 mm/min.
Experiments were performed on single stone columns and group stone columns arranged in square and triangular patterns. The selected area replacement ratios were 8.4, 12 and 16.4% for single, square and triangular stone column arrangements. To eliminate boundary effects, the distance between stone columns and the inner walls of the shear box was kept as high as 42.5 mm. In total, 11 direct shear tests were carried out, including two tests on loose sand bed material and stone column material, and 9 tests on stone columns with different arrangements. From the tests performed on group stone columns, 3 tests were performed on single stone columns, 3 tests on stone columns with square arrangement and 3 tests on stone columns with triangular arrangement. Hollow pipes with wall thickness of 2 mm and inner diameters equal to stone column diameters were used to construct stone columns. To prepare the specimens, first, the hollow pipes were installed in the shear box according to the desired arrangement. Then, bed material with unit weight of 16.5 kN/m³ was placed and compacted in the box in 5 layers, each 3 cm thick. Stone material was uniformly compacted to construct stone columns with uniform unit weight.
Results and discussion

1. The SCR value increases for settlement up to 3 mm and then decreases with increasing the horizontal displacement and then approaches almost a constant value. Results also show that stress concentration ratio decreases with increase of stone column diameter. Results show that the value of stress concentration ratio in square pattern is higher than that in single and triangular pattern. Moreover, results show that stress concentration ratio decreases with increase of normal stress.
2. The value of the internal friction angle in (peak) state, for loose bed increases from 33 to 40 degrees in square arrangement and in the corresponding state of displacement of 10 % from 30 degrees in a loose bed increase to 32 degrees, for loose sand reinforced with stone column. Shear strength increases with the increase of modified area ratio in all stone column installation patterns in both the peak and the corresponding state of the horizontal displacement of 10%.
3. For stone columns with the same modified area ratio, the installation pattern has an effective role in defining the shear strength. Group stone columns mobilize higher shear strength compared to single stone columns. Among the installation patterns investigated in this study, stone columns with square arrangement experienced the highest increase in shear strength value while single stone columns experienced the lowest.
4. The equivalent shear strength values measured from experiments are higher than those obtained from analytical relationships. Accordingly, it is conservative to use analytical relationships to calculate shear strength parameters. It is worth explaining that these relationships assume that the value of stress concentration ratio is equal to 1. Results from this study show that the value of stress concentration ratio should be accurately calculated and used in the relationships.
5. Comparison between shear strength parameters obtained from experiments and those predicted by analytical relationships shows that in single stone columns, the value of stress concentration ratio should be 3 to 4.5, and in square and triangular patterns, this value should be 6 to 7 and in triangular patterns 4.5 to 5, respectively, to achieve good agreement between experimental and analytical results in peak condition. In horizontal displacement 10% the value of stress concentration ratio should be 2.5 to 3, in single, square and triangular patterns, to achieve good agreement between experimental and analytical results../files/site1/files/151/2.pdf

---

Introduction
The ring footings are very important and sensitive due to widespread use in various industries such as oil and gas; so finding some ways for improving the behavior of these types of footings can be very valuable. One of these ways, which is very affordable and also can be help in environmental protection, is the use of granulated rubber that made from disposable materials like scrape tires, as the soil reinforcement. In the present study, the behavior of ring footings with outer constant diameter of 300 mm and variable inner diameters (90, 120 and 150 mm with inner to outer diameter ratio of 0.3, 0.4 and 0.5) placed on unreinforced sand bed and also granulated rubber reinforced bed, has been investigated by field test. The effects of important parameters like inner to outer diameter ratio of ring footing and thickness of rubber-soil mixture on the behavior of ring footing in terms of bearing capacity, settlement and inside vertical stresses of footing bed have been studied and the optimum values mentioned parameters have been determined.
Material and methods
In all tests, a sandy soil was used to fill the test trench which was excavated in the natural bed of the earth with a length and width of 2000 mm and a height of 990 mm. It should be noted that the type of this soil is well-graded sand (SW) according to the Unified Classification System (ASTM D 2487-11). This sand had medium grain size, D₅₀, of 2.35 mm, moisture content of 5.4% and friction angle of 41.7^∘. The granulated rubber particles with dimensions between 2-20 mm, a mean particle size, D₅₀, of 14 mm and a specific gravity, Gs, of 1.15, have been used in all tests for using in rubber-soil mixture layer.
The loading system consists of several parts such as loading frame for providing reaction force, hydraulic jack, load cell, load transfer system (including loading shaft which was located below Load cell and footing cap which was located under the loading shaft) and rigid steel loading plates with different inner to outer diameter ratios (d/D=0.3, 0.4 and 0.5 and constant outer diameter of 300 mm). Some devices like load cell, LVDT, pressure cell, data logger and unit control were applied to collect the data and control the system. Both soil and rubber-soil mixture layers were compacted by vibrating plate compactor to gain their maximum densities. After preparing the tests, the static load was applied on the system at a rate of 1 kPa per second until 1000 kPa or until backfill failure.
Results and discussion
The results of tests on both unreinforced and rubber reinforced beds indicated that the ring footing with inner to outer diameter ratio (d/D) of 0.4 had the maximum bearing capacity in all settlement levels. This behavior can be related to the arching phenomenon within the internal spaces of ring footing with optimum inner to outer diameter ratio. In fact, when the ring footing with optimum inner to outer diameter ratio is subjected to a certain level of loading, the soil inside the ring seems to be compacted due to interface effect of the two sides of the ring. However, by increasing the inner to outer diameter ratio more than its optimum value, the ring behaves like two independent strip footings without any interface effect and therefore the bearing capacity decreases.
The results of tests showed that the vertical inside stresses in different depths of footing bed (both unreinforced and rubber reinforced beds) decrease with increasing d/D ratio. This stress reduction process can be due to the transfer of stress concentration from the points close to the center of the ring to the outer point because of turning from the ring mode with interface effect to the two independent strip footings that mentioned earlier.
The results of rubber reinforced cases illustrated that, regardless of the footing settlement level and also irrespective of d/D ratio, the bearing capacity of ring footing increases with increasing the thickness of rubber-soil mixture layer (h_rs) up to the value equals 0.5 times the outer diameter of ring footing and further increase in this thickness more than mentioned optimum value (h_rs/D=0.5) can decrease the bearing capacity. Even in some cases of reinforced base (h_rs/D=1), the bearing capacity can be reduced to the value less than that of unreinforced cases. It can be due to high compressibility of rubber reinforced layers with higher thicknesses than optimum value.
It should be mentioned that the rubber reinforced layer can reduce the vertical inside stresses compared to unreinforced cases. It can be due to this fact that the rubber reinforced layer acts as a wide slab. Such that it can spread the applied loading over a wider area. Also rubber reinforced layer has high capacity of absorbing energy and therefore can decrease the vertical inside stresses.
Conclusion
In the present study the behavior of ring footing placed on rubber reinforced bed have been investigated by field test. The effect of different parameters such as inner to outer diameter ratio of ring footing and the thickness of rubber-soil mixture layer on the bearing capacity, settlement and vertical inside stresses of the footing bed were studied. The result indicates that:
- In both unreinforced and rubber reinforced bed, the ring footing with inner to outer diameter ratio (d/D) of 0.4 had the maximum bearing capacity, regardless of settlement level.
-The vertical inside stresses in different depths of footing bed decrease with increasing d/D ratio.
-The bearing capacity of ring footing increases with increasing the thickness of rubber-soil mixture layer (h_rs) up to the optimum value equals 0.5 times the outer diameter of ring footing.
-The vertical stresses can be reduced by using rubber reinforced layer../files/site1/files/151/5.pdf
 

---

Expansive soils contain clay minerals such as compacted kaolin which are widespread in nature. Displacements of this type of soils are associated with matric suction and degree of saturation. To determine the in-situ characteristics, necessary measures may be required to deal with the possible failure related to this type of soil. Different constitutive models of unsaturated soils have been considered the subject of many recent researchers (Sheng et al. 2004; Wheeler et al. 2003; Nuth and Laloui 2008; Zhang and Lytton 2009 a, b 2012). However, those constitutive models are generally complicated that are not properly implemented in computer programs for practical applications. The Barcelona Basic Model (BBM) is one of the geomechanical constitutive models to capture the elastoplastic behavior of unsaturated soils../files/site1/files/152/%D8%B5%D8%A7%D8%AF%D9%82_%D8%A2%D8%A8%D8%A7%D8%AF%DB%8C.pdf

---

Chahar-Gonbad region of Kerman province is geologically located in the southern part of central Iran zone, dominantly in Uromieh-Dokhtar volcanic belt. In this region, many high potential prospects, specially Cu-Au mineralization, have been detected during large scale exploration and reconnaissance phases. In this paper, remote sensing and field geophysics were used for alteration mapping on the surface and ore body delineation on the subsurface, respectively. To this end, we used an ASTER satellite image and different maps were generated by spectral technics such as false color composites and spectral ratios. Results showed argillic (and phillic) alteration in Bab-Zangoeie area is surrounded by propylitic alteration, which could be a promising evidence for Cu mineralization. Integrating these results with previous exploration studies led to selecting target area selection for ground study and field geophysics. We used both induced polarization (IP) and resistivity (RS) methods as two powerful geoelectrical methods by a pole-dipole array along four profiles. After preprocessing analysis, forward and inverse models were constructed in 2D section and 3D overlay model of joint IP/RS anomalies were constructed. Based on the obtained results, the deposit in depth where we proposed drilling targets. Further drilling operation have proved the mineralization in our proposed targets../files/site1/files/152/%D9%86%D8%B8%D8%B1%DB%8C.pdf
 

---

An accurate study of the physical-chemical properties of soil has a significant effect on the determination of mechanical parameters, classification and evaluation of soils, and the civil project management aspects. The obtained accurate results of the chemical parameters of soil can determine the type and amount of cement or lime used in stabilizing the problematic soils, which leads to better estimation of sub-channel substrate consolidation behavior, accuracy in engineering designs, and so on. Previous researches showed that the chemical changes such as increasing soil solutes are one of the affecting factors on the change of the mechanical parameters of the soil [1-3]. In this study, the effect of the waves on the saturated paste and the saturation extract was presented as a novel method in order to determine the soil chemical parameters as well as the soil dispersivity potential more precisely. Also, the effect of the waves on the arid and semi-arid regions can be considered as one of the environmental parameters affecting the solubility of solutes in the saturated soil and pre estimated dispersive and semi-dispersive of the soils../files/site1/files/152/%D8%B4%D8%A7%D9%87%D8%B1%D8%AE%DB%8C.pdf

---

In coastal industrial areas, in addition to the presence of loose soil, sulfate attack on soil improvement elements, such as soil-cement, is a double problem. Generally, the use of type V cement is recommended as one of the methods to reduce the detrimental effects. Considering the limited resources of this type of cement, firstly to determin the relationship between the cement content and the strength obtained in sulfated environments is one of the important engineering question in this field and secondly, as an alternative option, the use of type II cement which is more available, is suggested to use in combination with suitable additives. The present study pursues the above two goals by making cylindrical soil-cement specimens with sand, water and Portland sulfate resistant cements. Sodium sulfate is used as the sulfate in soil and water. In the research, first of all, the relation between type V cement content and unconfined compressive strength of soil-cement is obtained at 0% to 5% sulfate concentration, which results in a cement content of 400 kg/m³ completely limited the sulfate attack effects in a sulfate concentration of 2%. Secondly, the combination of type II cement with barium chloride and hydroxide was tested. The related results show that the combination of type II cement with barium chloride and hydroxide had higher strengths, about 2.7 to 3.3 times, respectively (in 362 days), than the soil-cement containing type V cement../files/site1/files/152/%D8%A2%D8%AA%D8%B4_%D8%A8%D9%86%D8%AF.pdf
 
 

---

Clayey soils in terms of sharp reduction in strength and swelling ability as a results of water and moisture absorption, it is considered as one of the most problematic soils in civil engineering and construction works. Nowadays, Nano materials such as Nano clay are used to improve and stabilize of clay. On the other side, the increasing volume of municipal waste and residues materials especially debris of building destruction have caused many problems in mega cities such as environmental issues due to incorrect disposal of waste material. Main propose of this research is study of possibility in effecting Nano clay and limestone powder mixture for improve geotechnical properties of Kuye Nasr clayey soil in Tabriz City. In this study, Nano clay and limestone powder in both separate and combined conditions with 5 and 10 percentage are mixed with clay. Curing of stabilized specimens have been performed in 7, 14 and 28 days. For evaluating geotechnical behavior of mixture materials some tests were performed such as Atterberg limits, Compaction, uniaxial strength and direct shear (in 1, 2 and 3 kg/cm2 vertical stress). Results show that the simultaneous effects of 5% Nano clay with 10% limestone powder with 7 days curing period in ambient temperature conditions in clay reduced plasticity index by 72%, improved graining skeleton structure, reduced void ratio of inter grains and increased shear strength by 33%.

./files/site1/files/%DA%86%DA%A9%DB%8C%D8%AF%D9%87_%D8%BA%D9%81%D8%A7%D8%B1%DB%8C.pdf
 

---

In this research work the effect of glycerol and acetone on the properties of a clay soil with low plasticity (CL) was studied through experimental tests. Contaminated soil was prepared by mixing 10, 15 and 20% pure glycerol or acetone with soil. A set of experimental tests including Atterberg limits, compaction, free swelling, Unconfined Compressive Strength (UCS), California Bearing Ratio (CBR), consolidation tests and Scanning Electron Microscopy (SEM) were conducted on uncontaminated and contaminated soil. The results showed that the effect of glycerol on contaminated soil was a reduction of Atterberg Limits, Free Swelling, optimum water content and increasing maximum dry unit weight but the effect of acetone was in the opposite trend of glycerol. These variations in the behaviors of soil were the function of percent of glycerol or acetone. In addition, the results indicated that both glycerol and acetone cause the reduction in the values of compressive strength and CBR number of soil but the reduction due to glycerol was more than the acetone. The results of consolidation test showed that the values of compression index (Cc) and swelling index (Cs) were independent of the percent of chemical fluids. The SEM results also reveal that these two contaminations cause some variations in the physical and mechanical properties of a clay soil becase of changing the structure of soil and the effect of these contaminations on the properties of soil was not the same.

Key words: hydrocarbon contamination, Atterberg limits, free swelling, Unconfined Compressive Strength (UCS), CBR and consolidation test.

./files/site1/files/%D8%A7%D9%81%D8%B3%D8%B1%DB%8C_%D8%B1%D8%A6%DB%8C%D8%B3%DB%8C(1).pdf

---

./files/site1/files/%D8%A7%D8%B9%D8%B8%D9%85%DB%8C_%D9%81%D8%A7%D8%B7%D9%85%DB%8C.pdf

---

In this study, due to the landslide in schist rocks, in the wall of Mouteh gold mines, including of the eastern wall of ChahKhatoon mine, it is important to identify the effective factors. Therefore, due to the diversity of schists in Chah Khatoon and Sanjadeh gold mines (two active mines in Mouteh Complex), to survey the mineralogy of schist rocks in Moteh gold mine has been done by identifying important factors in changes in rock strength. Cosequently, 10 schist samples from walls of these mines were considered for mineralogical, XRD studies. In the next step, these schists were subjected to uniaxial compressive strength (UCS) and Brazilian tests to estimate the mechanical properties and quality of rock mass in different zones of mineral walls. The results showed that the UCS and Brazilian index in these schists are directly and inversely related to the SiO₂ and Al₂O₃ contents of the rocks, respectively, as well as the secondary structures.Some factors such as the presence of secondary structures, continuous surface area, particle size, and mineralogical composition play an important role in the failure modes of these rocks. UCS and Brazilian strength of schists vary from 10 MPa to 72 MPa and 1.9 to 10.2 MPa, respectively. The lowest UCS occurs in strongly weathered rocks with low silica content. However, the type of clay minerals is effective in the stability of the mineral wall. Considering the presence of montmorillonite clay mineral in the eastern wall of Chahkhatoun mine, the rock resistance is moderate despite the high percentage of silica. UCS values of wet and dry rock samples containing muscovite and montmorillonite clay minerals were more different from those of other rocks. In this regard, the rocks with Illite clay minerals are more resistant than Smectite and montmorillonite minerals. In general, the resistance of schists depends on various factors such as mineralogy, which is of great importance because of its involvement in the formation of secondary structures.

./files/site1/files/%D8%AC%D8%B9%D9%81%D8%B1%DB%8C_%D9%82%D8%B1%DB%8C%D9%87.pdf
 

---

./files/site1/files/abstract_jandari.pdf

---

---

./files/site1/files/%DA%86%DA%A9%DB%8C%D8%AF%D9%87_%D9%85%D8%A8%D8%B3%D9%88%D8%B7_%D8%A8%D9%87_%D8%A7%D9%86%DA%AF%D9%84%DB%8C%D8%B3%DB%8C_(1).pdf

---

Soil stabilization and reinforcement has long played an important role in civil engineering, especially in geotechnics, and over time and the need for a more robust and stable ground to withstand gravity and higher shear forces, has become particularly important. Also, in recent years, with the entry of the environment into the construction industry, with the aim of reducing the adverse effects of industrial waste and construction waste on people's living environment and preserving the environment for the future, in many cases reduces the economic costs of projects. In this research, granular soil is reinforced in two loose and semi-dense states using a waste material called ethylene-vinyl acetate (EVA). The experiments were performed without adding moisture, by weight percentage method and using CBR device. The results show that soil resistance increases significantly with the use of these additives and its effect on soil increases with decreasing soil specific gravity. Also, the optimal amount of additives in loose and semi-dense state is 2% additive and 1% additive, respectively.


./files/site1/files/%DA%86%DA%A9%DB%8C%D8%AF%D9%87_%D9%85%D8%A8%D8%B3%D9%88%D8%B7_%D8%A7%D9%86%DA%AF%D9%84%DB%8C%D8%B3%DB%8C_%D8%B3%D9%87_%D8%B5%D9%81%D8%AD%D9%87_%D8%A7%DB%8C.pdf

---

./files/site1/files/abstract_amini.pdf

---