Showing 185 results for Type of Study: Original Research
, ,
Volume 14, Issue 1 (5-2020)
Abstract
Introduction
Geofoames are used as a light weight fill material in those places which soil borrows is not cost effective for engineering or economic purposes. In general, geofoames are highly capable of improving some of geotechnical properties of soils such as inflation creation, reduction of density, and etc., due to their light weight, no change of volume against water, low permeability, and relatively proper strength. Using mixture of geofoam beads and soil has been recently taken into consideration by researchers. The mixture causes tangible reduction of soil density and severe drop of active pressure of retaining walls. Also, using the mixture in seismic zones is of special importance. In the paper, effect of mixing geofoam (4 different percent) and three types of poorly graded sandy soils have been dealt with. The research innovation has been compared to previous ones is using poorly graded sandy soil, separating geofoam beads based on their diameter, and reviewing the effect of adding various percentage of geofoam on improvement of poorly graded sandy soil’s properties.
Materials and Test Method
Tests have been performed in direct shear box (10 cm x10 cm) under three stress levels of 50, 100, and 150kPa. First type of soil has been Firoozkooh sand (#161) with specific gravity of 2.65, as uniformly graded sand (SP). Second type of soil has been mixture of uniformly graded sand and 10% silt (SM-SP); and, third type of soil has been mixture of Firoozkooh sand and 20% silt (SM). The three above types of soils have been named as soil 1, soil 2, and soil 3, respectively.
Geofoam beads have been all fine grained, passing through sieve No. 10; and, their added weighted values have been 0, 0.2, 0.4, and 0.6% of weighted percentage of soil. All of tests have been performed with optimum moisture content of geofoam and soil mixture. Due to diversity of soil types and ratio of geofoam-soil mixtures, soil compaction test has been performed on each direct shear test’s sample to specify optimum moisture content of various types of mixtures; because there have been various types of soils used, and also various ratios of soil and geofoam mixtures.
Results
According to the results, using geofoam beads leads to considerable reduction of soil density. Decrease made in density will be more tangible when higher percentages of geofoam are added to the soil. Also, as far as geofoam absorbs water, optimum level of moisture will be increased through increase of geofoam percentage in soil-geofoam mixture.
Since geofoam beads are less rigid compared to grains of sand, sand and geofoam interlocking and friction level is lower than sand interlocked to sand; and shear strength has been decreased through increase of geofoam percentage in soil. The point to be remembered is that, reduction level of shear strength in soils containing various percentages of geofoam is not so tangible compared to the soil itself. In its worst case, the reduction would be about 12%.
Adding geofoam beads to all of the three types of soil has led to their increase of apparent cohesion. Moreover, through increase of mixture percentages, more increase has been made in apparent cohesion of mixture. The results are indicative of significant effect of mixing geofoam and soil 1 in increase of soil cohesion up to 9 times. The cohesion increase has been about 4 and 2 times for soils type 2 and 3 respectively. So, it could be concluded that the lower the soil cohesion, the higher would be effect on cohesion increase of soil, through increase of geofoam percentage.
In figure 1, chart of internal friction angle is shown based on mixture percentage of geofoam for those types of soils being tested. Considering decrease of internal friction angle through increase of geofoam percentage, the important point is slope drop observed when geofoam percentage added has been 0.4%. Therefore, reduction speed of internal friction angle has become slower, after this level. Considering the figure, internal friction angles of soils type 1, 2, and 3 have shown respectively 15, 16, and 18% of reduction, through highest percentage of geofoam added (0.6%).
Figure 1- Internal friction angle based on geofoam percentage mixed with different soils
Comparing the results from present and previous researches, it could be concluded that adding higher percentages of geofoam results in cohesion increase of sandy soils; however, the increase level is different for various types of soils. The lower the initial cohesion of sandy soils and the more uniform their gradation, the more the effect of adding geofoam on increase of cohesion coefficient of soil. Also, downward trend of internal friction angle for well graded and poorly grades sandy soils is almost similar.
Using the results from present research and considering acceptable level of reduction made in internal friction angle of the soil mixed with geofoam against cohesion increase and reduction of soil density; mixture of geofoam beads and soil could be used in construction of embankments, retaining walls and other earth structures, appropriately.
Mohammad Hossein Ghobadi, Mehrdad Amiri, Farhad Aliani,
Volume 14, Issue 1 (5-2020)
Abstract
Because of the diversity in petrography, peridotites have variable physical and mechanical properties. For this reason, knowledge of resistance properties and their deformation will help with the prediction of engineering behavior of these rocks. Due to the large spread of igneous rocks, especially peridotite, in Zagros, northeastern and central Iran, special attention has been paid to their petrographic, physical and mechanical characteristics. The construction of the structure within or on the peridotites and the choice for the purpose of the stone borrow depends on the recognition of its engineering geology characteristics. In this paper, in addition to the field and laboratory study, the geological characteristics of peridotite engineering has been investigated.
Material and methods
In order to study the geological characteristics of the peridotites of Harsin region, 15 suitable blocks were selected and transferred to the laboratory. Accordingly, from collected rock samples, 150 cylindrical cores of diameter 54 mm were prepared and physical and mechanical tests were performed according to (ISRM, 2007) and (ASTM, 2001) guidelines. In this research, after sampling of the study area and preparing the core for the lithological characteristics of the samples by providing thin sections of them with polarizing microscopy was studied.
Results and discussion
By considering the results of laboratory tests and analysis from Harsin peridotites in Kermanshah province, we can acclaim that with increasing the percentage of minerals in olivine and pyroxene in rock, the strength was decreased and the levels weaknesses, which is due to the weak structure of the mineral-olivine and pyroxene. According to the physical properties test and Anon classification, the porosity percentage in porosity percentage is low and as a result the amount of water absorption index is low. Based on the Gamble classification, all peridotites are very resistant to durability and based on the Franklin and Chandra classification, all samples are extremely resistant. The results of this study showed that the single axial compressive strength, elasticity modulus, point load index and tensile strength were decreased with an increase in humidity content of peridotite samples. This is due to the fact that with the increase of humidity pore pressure of water increases. According to the Anon classification, the peridotites are very high in terms of the length of the longitudinal passage through the rock. The highest compliance between the Brazilian Tensile strength test (BTS) and Schmidt hammer (SHV) was achieved in the dry condition and the determination coefficient (R2) equals to 0.95 was obtained. Also there is an acceptable relation between the Brazilian Tensile Strength Test (BTS) and the dry volume unit weight (γd) with the determination coefficient (R2) of 0.93. In addition, there is an admissible relationship between durability test and single-axial compressive strength, with a coefficient determination (R2) of 0.94. Regarding the obtained regressions in this study, the physical and mechanical properties show good agreement and most of the equations have an acceptable coefficient determination.
Mohammad Emad Mahmoudi Mehrizi1, Younos Daghigh, Javad Nazariafshar,
Volume 14, Issue 1 (5-2020)
Abstract
The increasing rate of construction activities in urban areas is accompanied by excavation in the vicinity of existing structures and urban utilities. This issue has highlighted the importance of constructing protecting structures in order to control displacements and prevent damage to structures and their neighboring area. Among the important widely used wall stabilization techniques, one can name nailing and grouted anchors. However, these methods suffer some drawbacks such as annoying noise and vibration during the drilling, implementation difficulties below the water table, grouting problem, installation of strands and bars in the borehole in porous and collapse soils, and long curing time for the grout of post-tension anchors. Since the helical anchor method lacks many of the mentioned problems, it is now widely used in many applications.
In the present work, a laboratory model of helical anchor stabilized wall is presented and evaluated. For this purpose, four types of anchors at 20° back slope are designed in a sandy soil and the effect of helix configuration (in term of its diameter and number of blades) is investigated. Considering the laboratory scale of the designed model, the results obtained using helical anchor were compared with numerical results of soil nailing wall by applying the particle image velocimetry (PIV) analyses.
Material and methods
The test box designed in this work is made of a metal plate with a thickness, length, width, and depth of 1.5 mm, 100 cm, 60 cm, and 30 cm, respectively, and a Plexiglas in its opposing side with a thickness of 50 mm. The soil used in the experiments was the dry sand of Soufian region in east Azerbaijan province of Iran. The soil is classified as SP according to USCS classification. The helical anchors were fabricated by welding the helical pitches to a metal shaft. The end part of the shafts is screw threaded such that to fasten a bolt to them.
To start the experiment, the empty box was completely cleaned using the detergents to remove any pollution or soil on the Plexiglas and metal surface. Afterward, the sandy soil was poured on the wall floor and the facing was placed inside the box vertically. Again, the sandy soil was poured from both sides of the facing up to the installation height of the helices. Helices were installed in the assigned holes and their angle was adjusted through the pre-fabricated stencils. The soil height was increased up to the next row assigned for helices installation. These steps were repeated until reach the wall crest. After preparation of the physical model, its behavior during the preparation must be modeled. We first filled both sides of the model and then modeled the stability behavior of the helical anchor wall through excavating its facing opposed side. Overall, the wall was built through eight excavation steps.
Results and discussion
The maximum displacement is related to the anchor type 1, which does not have enough bearing capacity under surcharge conditions. By changing the anchor type and increasing the number of helices, shear strains and their expansion in the wall back decline. The decrease in displacement rate by changing the anchor from type 1 to type 2 is 18%, which is due to the low bearing capacity of type 2 anchor compared to the type 1 anchor. Increasing the number of pitches from one to two (changing the type 1 anchor to type 3 anchor) showed a considerable decrease (i.e., 43%) in displacement rate. Increasing the number of pitches from 1 to 3 (changing the anchor from type 1 to type 3) resulted in a 62% decrease in wall crest displacement. This displacement decrease rate seems to decline with an increase in the number of helixes.
The displacement rate for all four anchors is almost similar in two excavation steps, which probably is because of the need for displacement for activation of the anchors. One strategy to deal this issue in the sensitive projects and control the displacement is to apply post-tension helical anchors. Then, in stages 4 to 6, the displacement was almost constant due to four main reasons including wall rigidity, the presence of reinforcements, formation of pre-step displacement-induced tension force, and enough capacity of anchors to face with more displacement. In stages 6 to 8, type 1 and 2 anchors showed growing displacements due to the reduction and ending the wall rigidity and lower bearing capacity. In type 3 and 4 anchors, the maximum displacement was related to 4 initial stages. In type 1 and 2 anchors, which have two helical plates, almost a similar behavior was observed until stage 6 of excavation, but eventually type 3 anchors showed better performance because of higher bearing capacity to overall displacement.
Conclusion
In the present study, a physical model was designed to investigate the effect of helical anchors’ geometry on displacement rate of helical anchor wall and compare it with a nail wall. Overall, comparing the results obtained by conducting these experiments on a helical anchor stabilized wall and a nail wall revealed that:
- Wall crest displacement is affected by the diameter and number of helices and decreases by an increase in bearing capacity.
- The increase in the number of pitches from one to two (single-pitch to double-pitch anchor) has a higher effect on displacement control compared to the case of changing the double-pitch to triple-pitch anchor. So, it can be stated that a further increase in the number of anchor pitches results in a declined performance of the anchors.
- All anchors need a slight displacement for activation. This issue cannot be resolved by changing the type of helical anchors. Hence, when the displacement required for activation of the anchors exceeds the allowable wall crest displacement, use of post-tensioned helical anchors is recommended.
- A comparison between nailing and helical anchor results revealed that the relative density of the wall stabilized with the helical anchor is less than that of the nail wall; and wall crest displacement in the helical anchor wall was very lower than that of nail wall. Thus, the helical anchor wall stabilization is preferred when other economic and technical requirements are met.
Mohammad Mahdi Aminpour1, Mohammad Maleki,
Volume 14, Issue 1 (5-2020)
Abstract
Introduction
Studying the effect of slope angle on bearing capacity of foundations on the slope in urban areas is a challenging problem that has been investigated by researchers for years. In general, the analytical approaches for solving this problem can be categorized into limit equilibrium, characteristics and limit analysis methods. In recent years, there have been studies for using the limit analysis within the framework of finite element method for geomaterials. In these studies, the soil mass is not considered as rigid and there is no need to predefine a failure surface for the slope. In the performed research, using the upper bound finite element limit analysis, bearing capacity of strip foundation on slope have been studied. This analytical method enables the use of the advantages of both methods of limit analysis and finite element analysis. In this method, the slip between the two elements is considered. In order to find the critical state of the failure, the rate of power internally dissipated is linearly optimized, by using the interior points method. The advantages of this method are the high convergence rate in comparison with other analytical optimization methods. The effect of different upstream and downstream slopes and foundation depths and also the influence of various mesh discretizations have been evaluated. Finally, the results are compared with those obtained from previous methods available in the literature.
Methods
The finite element limit analysis method is based on nodal velocities. Considering the principals of the finite element method and having the nodal velocities, the velocity at each node of the element can be obtained from corresponding shape functions. The rate of power internally dissipated in each element is defined by multiplying the strain rate on stress in each element. In this method, the slip between the two elements and the rate of internal power dissipated at each discontinuity of two adjacent elements is considered. For this purpose, in each node, four new unknowns’ velocities are defined. To remove the stress from the equations, and provide a linear relationship for linear optimization, a linear approximation to the yield function has been used. For this purpose, the Mohr-Coulomb yield criterion is estimated with a polygon in the stress space. Also, using the reduced strength parameter, the effect of the dilation angle is considered. According to the principles of upper bound limit analysis, the value of plastic strain rate is calculated from the flow rule. The velocity field in elements and discontinuities must satisfy the set of constraints imposed by an associated flow rule. In order to have an acceptable kinematics field, the velocity vectors have to satisfy the boundary conditions. These conditions include zero kinematics velocities along the vertical and horizontal boundaries of the geometry as well as negative vertical unit velocities and zero horizontal velocities at points underneath the rigid foundation.
Results and discussion
In order to calculate the bearing capacity of foundation, a set of different uniform and non-uniform mesh has been examined. The results obtained from different uniform mesh sizes indicate a certain divergence in the course of analysis. However, the results between the fine and very fine non-uniform mesh are closely related to each other and are converged. The obtained results show that, by increasing the internal friction angle, the bearing capacity has been increased. At high angles of modified friction, the effect of increasing the internal friction angle on the increase in bearing capacity is more in slopes with lower angles. By increasing the downstream foundation depth, the bearing capacity has been increased. This increase is more important in the case of slopes with lower angles. However, the upstream depth variations didn't present a significant effete on bearing capacity. In order to investigate the effect of upstream angle on the bearing capacity, the upstream mesh is also refined similar to the downstream. The obtained results indicate that variations of the upstream angle have a minor effect on the bearing capacity. This is of course true if the upstream slope is fully stable. The results of the proposed method in this study are an upper bound for the results reported by the limit equilibrium and displacement finite element methods. As seen in Figure 1, the suggested method predicts lower bearing capacities compared to rigid block limit analysis method and is indeed a lower bound for the classical limit analysis method. The finite element limit analysis with linear optimization has resulted in more bearing capacity than cone optimization. The bearing capacities, obtained from characteristic lines method depending to the slope angles, in some cases is more and in some cases less than those explored by the proposed method.
In this paper, the bearing capacity of foundation located on slope was evaluated by finite element limit analysis method. In this regard, the effects of different downstream and upstream angles of slope and foundation depths and also, the effect of various mesh discretizations on the bearing capacity were studied. It is shown that an increase in the downstream angle causes a decrease in the bearing capacity and an increase in the downstream foundation depth leads to an increase in the bearing capacity. However, the upstream angle and upstream foundation depth were not much effective on the bearing capacity.
, , ,
Volume 14, Issue 1 (5-2020)
Abstract
Mehdi Jalili, Hosein Saeedirad, Mohammad Javad Shabani,
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
Dispersive soils are problematic and they cause a great many of local damages and destructions in hydraulic structures such as dikes and irrigation channels. The correct identification and recognition of divergence are fundamental measures taken in line with preventing the early destruction of the hydraulic structures. The soil improvement using lime, especially in clayey soils (CL), brings about an increase in the optimum moisture percentage, reduction of the maximum dry unit weight, reduction of swelling potential, increase in the strength and elasticity module. The effect of lime on soil can be classified into two groups, namely short and long-term stabilization. Raise of the soil’s workability is
counted amongst the short-term modification measures and it is the most important factor in the early improvement stages. The increase in the strength and stability can be considered as the lime utilization on long-term results occurring during curing and afterwards. Also, according to the reports, swelling and damages occur in the lime-stabilized soil containing sulfate. The effective role of the iron furnace slag has been well recognized in increasing the strength against sulfates and corrosive environment conditions of the mortar containing lime and sulfates.
Material and methods
Adding the slag products of the melting furnaces and lime is a method used to stabilize dispersive soils. The present study makes use of a mixture of clay featuring low plasticity with 1% and 2% lime and slag, for 0.5%, 1%, 3% and 5% of the weight, to improve dispersivity, shear strength and plasticity. The samples were kept in constant temperature and humidity for a day and then were subjected to direct shear, uniaxial strength and pinhole tests.
Results and discussion
It was observed based on pinhole experiment of the initial dispersive soil sample, denoted as D1, that the sample, shown by ND2, containing lime, for 2% of the weight, and slag, for 5% of the weight, turned out to have become non-divergent. The results of the direct shear test showed that the adhesion coefficient of the slag-free samples stabilized using 1% lime has been increased from 0.238 kg/cm
2 to, respectively, 0.251 kg/cm
2, 0.373 kg/cm
2, 0.41 kg/cm
2 and 0.48 kg/cm
2 per every 0.5%, 1%, 3% and 5% slag added. The adhesion of the samples stabilized using 2% lime as determined in the direct shear experiment were 0.615 kg/cm
2, 0.671 kg/cm
2, 0.724kg/cm
2 and 0.757kg/cm
2 per every 0.5%, 1%, 3% and 5% slag added. Also, the internal friction angle of the samples stabilized using 1% lime was found an increase from 14.3° for slag-free samples to 18.11°, 21.3°, 21.86° and 21.92° per every 0.5%, 1%, 3% and 5% added slag. As for the samples stabilized using 2% lime, the internal friction angles were found in direct shear test equal to 23.15°, 23.53°, 23.76° and 24.12° per every 0.5%, 1%, 3% and 5% slag added. The uniaxial strength of the slag-free samples stabilized using 1% lime was found an increase from 1.0014 kg/cm
2 to, respectively, 1.0616 kg/cm
2, 1.0782 kg/cm
2, 1.2127 kg/cm
2 and 1.2246 kg/cm
2 per every 0.5%, 1%, 3% and 5% slag added. The uniaxial strength rates has been determined in the direct shear test of the samples stabilized using 2% lime were 1.1367 kg/cm
2, 1.1885 kg/cm
2, 1.2322 kg/cm
2 and 1.2872 kg/cm
2 per every 0.5%, 1%, 3% and 5% slag added. The amount of axial strain of the slag free samples stabilized using 1% lime was found decreased from 9.6842% to, respectively, 9.3333%, 9.2683%, 9.6364% and 8.4444% per every 0.5%, 1%, 3% and 5% slag added. Moreover, the axial strain amounts obtained for the samples stabilized using 2% lime were 7.7333 kg/cm
2, 7.6316 kg/cm
2, 7.1517 kg/cm
2 and 4.7619 kg/cm
2 per every 0.5%, 1%, 3% and 5% slag added.
The study results indicate that slag and lime have the capacity of improving the studied soil’s dispersivity. Furthermore, it was figured out that adding slag to the soil causes an increase in the soil strength and improves the shear strength parameters. It can be stated according to the observed results that the use of slag, a byproduct of iron smelting industry, as a substitute for a given percentage of lime is effective on the reduction of the clay soil’s divergence potential. The results of the experiments carried out to determine Atterberg limits are suggestive of the idea that the increase in the slag and lime fractions brings about a decrease in the liquid limit and plasticity and improves the plasticity properties of the soil. The reason why the soil plasticity has been reduced after being mixed with lime and slag is the cationic exchange and coarsening of the soil texture. Addition of lime to the soil causes an increase in the plasticity limit and a reduction in the liquid limit. Therefore, the plasticity index is decreased and the plasticity characteristics of the soil are improved. Adding 1% lime to the dispersive soil leads to small reduction of the liquid limit from 32.43% to 31.73%, a small increase in the plasticity limit from 13.42% to 14.66% and a insignificant decrease in the plasticity index from 19.01% to 17.07%.
Hadi Bahadori, Amin Khalili,
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
Soil dynamic properties are used to evaluate the dynamic response of soils at different strain levels in geotechnical engineering. The shear modulus (G) and damping ratio (D) are among the most important dynamic properties of soils. In general, the factors affecting the dynamic behavior of soils are divided into two categories: first; soil type and characteristics such as water content, void ratio and soil plasticity and second; parameters of loads applied on the soil such as the number of loading cycles, loading frequency and loading waveform .Therefore, it is widely believed that the dynamic response of soils partially depends on the characteristics of the load. In this paper, 1-g shaking table tests were employed to investigate the effect of loading waveform and frequency content on dynamic properties of dry sands. The response obtained from soil samples during loading with different frequencies, input accelerations and waveforms were used to generate hysteresis loops of tested samples at different strain amplitudes. Then, hysteresis loops were used to determine the damping ratio and shear modulus at different strain levels. Finally, the effects of loading frequency and waveform on the changes of each parameter (G and D) were investigated.
Material and methods
A hydraulic shaking table with a single degree of freedom, designed and constructed at the Crisis Management Center of Urmia University, was used to conduct the experiments. Firoozkuh No. 161 sand was used in all the experiments. The Firoozkuh sand gradation curve is similar to that of Toyoura sand. In this study, accelerometers were used to measure the acceleration of the input to the sample as well as to record the acceleration caused by the input excitation at different depths of the soil sample. The displacement transducers (LVDT sensors) were also used to measure linear displacement. Each soil sample was constructed using dry Firoozkuh sand poured uniformly into the container from four equal heights of 150 mm to reach a total height of 600 mm. During the compaction process, the accelerometers A
1, A
2, and A
3 were placed at a depth of 150, 300 and 450 mm with respect to the bottom of container. Also, one accelerometer, A
0, was attached rigidly to the container base to measure base acceleration. A displacement transducer (L
1) was placed on the soil surface at a height of 600 mm from the floor of the container to measure the vertical displacement of the surface of the soil. In this study, 42 shaking table tests were performed to study the effect of loading frequency and waveform on dynamic properties of dry sand. The test samples were subjected to rectangular, sinusoidal and triangular loading at frequencies of 0.5 to 9 Hz and at input acceleration of 0.1g and 0.3 g.
Results and discussion
Given the importance of G-γ and D-γ curves in dynamic analyses, the changes in shear modulus with shear strain has been studied. The results show that the shear modulus increases as the frequency increases in all cases, and this increase is observed at lower frequencies and increases with increasing frequency. On the other hand, the shear modulus decreases with increasing shear strain. At a constant testing frequency, soil samples subjected to the rectangular waveform exhibited the largest shear modulus while the samples subjected to the triangular waveform showed the least shear modulus. The shear modulus of the samples under the sinusoidal waveform is barely more than the shear modulus of samples under triangular waveform. Moreover, by increasing the shear strain, the shear modulus values of samples with different waveforms have become closer and the waveform effect is reduced. As for the effect of input acceleration on the shear modulus , increasing the input acceleration increases the shear strain and consequently, decreases the shear modulus in all states (the values of shear modulus in various frequencies and the waveforms under the input acceleration of 0.1 g are larger than the shear modulus values under the input acceleration of 0.3g). In the case of the damping ratio, the results show that, in all cases, damping ratio increases with shear strain. At low strain levels, the damping ratio values at various frequencies and waveforms are low and yet very close. At higher strain levels, the increase in frequency increases the damping ratio. This increase is more significant at higher frequencies. Also, the effect of waveform on the damping ratio is more apparent at larger shear strains, and at such shear strain levels, soil samples under rectangular loading exhibit the largest damping ratio. The damping ratio associated with the sinusoidal and triangular loading are also close to each other and it is a slightly larger for sinusoidal loading. On the other hand, the damping ratio increases with input acceleration. In addition, the effect of increased input acceleration on the increase in the damping ratio is more obvious at higher frequencies mainly due to the increase in shear strain.
Conclusion
In the present study, the effects of loading frequency and waveform on the dynamic properties of dry sand were investigated using shaking table tests. The following conclusions were drawn:
- The shear modulus increases with frequency. The trend is more obvious at larger frequencies. The effect of loading frequency on the damping ratio of the soil at low levels of strain is negligible, and at relatively large strain levels, damping ratio increases with loading frequency.
- Soil samples exhibit the highest shear modulus and damping ratio under rectangular loading. Therefore, in all the tested frequencies and input accelerations, the values of G and D for the rectangular waveforms are greater than those of the sinusoidal and triangular waveforms. The shear modulus and damping ratio for the sinusoidal waveforms are marginally greater than those of triangular waveforms, yet one can consider them practically similar.
- In all cases, the shear strain increased by increasing the amplitude of the input acceleration, and as a result, the shear modulus decreased and the damping ratio increased../files/site1/files/142/2.pdf
Bakhtiar Fezizadeh, Meysam Soltani ,
Volume 14, Issue 2 (8-2020)
Abstract
Introduction
Landslide is known as one of major natural hazards. Landslide susceptibility mapping is known as efficient approach to mitigate the future hazard and reduce the impact of landslide hazards. The main objective of this research is to apply GIS spatial decision making systems for landslide hazard mapping in the 5
th segment of Ardebil-Mianeh railroad. Evaluation of the landslide criteria mapping and their relevancy for landslide hazard can be also considered. To achieve the research objectives, an integrated approach of Fuzzy-Analytic Hierarchy Process (AHP), Fooler Hierarchical Triangle and Fuzzy logic methods were employed in GIS Environment.
Material and methods
Within this research, we also aimed to apply GIS spatial decision making systems and in particular GIS multi criteria decision analysis which are available in Arc GIS and Idrisi softwares. We have identified 8 casual factors (including: density of vegetation, land use, faults desistance, distance from rivers, distance from roads, slope, aspect, geology) based on literature review. Accordingly, these layers were prepared in GIS dataset by means of applying all GIS ready, editing and topology steps. The criterion weighting was established based F-AHP approach. The criteria weights was derived and rank of each criterion was obtained. Accordingly, the landslide susceptible zones were identified using GIS-MCDA approaches.
Results and discussion
Finally the functionality of each method was validated against known landslide locations. This step was applied to identify most efficient method for landslide mapping. According to the results and based on the values derived from
Qs,
P, and
AUC, the accuracy of fuzzy method was accordingly about 0.33, 0.74 and 0.76, respectively. In context of Fuzz-AHP the accuracy of 1.08, 0.88 and 0.94 were obtained. While, the accuracy of Fooler Hierarchical Triangle were obtained 0.78, 0.84 and 0.91, accordingly.
Conclusion
As results indicated integration of Fuzzy-AHP represented more accurate results. Results of this research are great of important for future research in context of methodological issues for GIScience by means of identifying most efficient methods and techniques for variety of applications such landslide mapping, suitability assessment, site selection and in all for any GIS-MCDA application.
Semaneh Ghasemvash, Rouzbeh Dabir,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Pavement layers as a part of road structure play an important role and provide a flat and secure surface. Subgrade layer could act as a compacted embankment, natural or stabilized ground. Subgrade is a foundation of pavement layers, and it withstands all of loads due to vehicles that are transferred from upper layers (i.e., subbase, base and asphalt layers).Therefore, constructing pavements with bearing capability, high durability, quality, and maintenance in proper operating conditions is very important. However, suitable materials for constructing pavement layers are not available, and improvement techniques should be employed for them. Generally, different methods such as mechanical or chemical are available for improvement. Nowadays, geosynthetic materials such as geotextile and geogrid are used to optimize and enhance the bearing capacity of pavement layers. The present study is aimed to investigate the effects of geotextile applications on bearing capacity of clay-gravel mixtures in pavement layers.
Material and Methods
In this research, materials were prepared from Barandouz area. Clayey soil was mixed with gravel in 25, 50 and 75 percentages (by weight). Geotextile was woven and made of polypropylene (with commercial name Fibertex-F-32). Geotextile effects in mixture were evaluated in two conditions. Position number one indicates the arrangement of geotextile. This means, at first, one geotextile layer was embedded in the middle of materials. Then, two and three geotextile layers in equal depths from each other were used in soil mixtures. Position number two shows the mixing pieces randomly. This means that geotextile pieces in 1×1 and 5×5 cm2 were prepared and were randomly mixed with materials in 1, 2 and 3 percentages (by weight). For evaluating geotechnical behavior of improved clay-gravel mixtures, compaction and California bearing ratio test (CBR) (in dry and saturate conditions) based on ASTM were performed.
It should be noted CBR test in dry and saturate conditions were carried out in three different compaction energies (i.e. 10, 25 and 56 blow count for per layer). Moreover, CBR was evaluated for piston penetration at 2.5 and 5 cm in the specimen.
Results and discussion
The findings of this study could be summarized as:
1. Results of compaction test showed that, in the unimproved position, with increasing gravel content in clay, maximum dry unit weight (γdmax) has been increased, while simultaneous optimum water content (wopt) decreased.
In the improved position, in the first mode, when a geotextile layer was embedded in the middle of the specimens, γdmax reached to its upper value, whereas wopt reached to its minimum value. On the other hand, with an increase in the number of geotextile layers in clay-gravel mixtures, dry density has been decreased, but optimum water content increased. Furthermore, in the second mode, when geotextile pieces with 1×1 and 5×5 cm2 were randomly mixed in the specimens, the findings revealed that geotextile pieces with 1 cm2 areas and 1% by weight in clay-gravel mixtures increases γdmax and reduces wopt.
2. In dry and saturate conditions, California bearing ratio (CBR) test result displayed that in the unimproved condition, with an increase in gravel content in the clay, CBR value has been increased. In the improved situation, in the first mode, when a geotextile layer was embedded in the samples, CBR had a maximum value in all of the compaction energies even though it is reduced as the number of layers increased. In the second mode, when geotextile pieces in 1×1 cm dimensions with 1% (by weight) were randomly mixed with the specimens, CBR value reached at high. In contrast, with increasing dimensions of pieces and percentages in the presence of geotextile in clay-gravel mixtures, CBR values declined. Therefore, it can be concluded that, according to Code 234 (Iran Highway Asphalt Paving Code), the application of one geotextile sheet in the middle of materials or geotextile pieces in 1×1 cm dimensions with 1% (by weight) random mixing is suitable for subbase and base layers in pavement design.
3. CBR test results in the saturate condition in clay-gravel mixtures illustrated that, in the non-reinforced condition, with an increase in clay content in specimens, swelling value keeps rising sharply. On the contrary, in the reinforced position with embedding a geotextile layer in the middle sector of samples or through adding geotextile pieces (1 cm2) with 1 % content (by weight) to the specimens, the rate of swelling significantly decreased.
Conclusion
To sum up, the main objective of the present study was to investigate the impact of geotextile applications on bearing capacity of clay-gravel mixtures in pavement layers. The findings demonstrated that when geotextile as a layer was embedded in the middle part of specimens or as pieces with 1×1 cm dimensions and 1% content (by weight) was randomly mixed with the mid materials, the bearing capacity of the reinforced specimens was enhanced. In contrast, in the saturate condition, swelling potential significantly was reduced. It is noteworthy to mention that 1 cm2 pieces of geotextile is more effective than the layers. This is due to the fact these pieces make aggregates closer to each other. Thereby, minimum void ratio (emin) reaches its least value, the structure of grading improves, and the contacts between particles and geotextile pieces rise. As a suggestion for further research, it looks promising to evaluate the dynamic properties and the behavior of the improved materials with other geosyntheticses.
Moslem Babaei, Ali Raeesi Estabragh, Jamal Abdollahi, Mohadeseh Amini, Gholamali Vakili,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Expansive soils are a very common cause of extreme damages because they are susceptible to volume change due to a change in water content. Geotechnical problems associated with the expansive soils are well documented in different literature. As a result, a clear understanding of the behavior of such soils is required for the effective design of structures and infrastructures on these soils. The effects of hydrocarbon pollutants as a flooding fluid on the swelling potential of an expansive soil during wetting and drying cycles have not been considered in the previous researches. The aim of this research is to study the properties of an expansive soil with different flooding fluids, i.e. distilled water and solutions of glycerol with 10 and 20% through a number of cycles of wetting and drying tests under constant surcharge pressure.
Material and methods
The soil that was used in this work was a highly expansive clay soil
(according to the classification by McKeen (1992)). It was prepared by mixing 20% bentonite and 80% kaolin. This soil was classified as a clay with high plasticity according to the Unified Soil Classification System (USCS). The optimum water content in the standard compaction test was 18.11% and the maximum dry unit weight was 16.27 kN/m
3.
Distilled water and solutions of glycerol with concentrations of 10 and 20% were used for flooding the samples. To prepare the glycerol solutions, the required amount of glycerol was mixed with distilled water.
For making compacted samples for testing, the needed air-dried soil was weighed and the required water was added to it to reach the desired water content (4% below the optimum water content according to the compaction curve). The soil and water were mixed by hand and then was kept in a plastic bag for 24 hours to allow the uniform distribution of moisture in the soil. Samples were prepared by static compaction of the moist soil in a special mould.
A conventional oedometer was modified to allow the wetting and drying tests to be conducted under controlled surcharge pressure and temperature. During wetting and drying, the vertical deformation of the sample was measured by using a dial gauge. The variation of water content with void ratio during wetting and drying cycles was determined by using the information from the duplicated samples.
Results and discussion
Fig. 1 shows the variations of vertical deformation during wetting and drying cycles for samples that were flooded with distilled water and solutions of 10 and 20% glycerol. This figure illustrates that by increasing the number of cycles the amount of irreversible deformation is reduced until the equilibrium condition is achieved where the deformation due to wetting and drying is nearly the same. These results indicate that by increasing the concentration of glycerol the equilibrium condition with reversible deformation is reached in a fewer cycle of wetting and drying than the sample that was flooded with distilled water.
Figure 1. Wetting and drying cycles for different quality of flooding fluids
The results of void ratio versus water content at the equilibrium conditions for the samples flooded with distilled water and solutions of 10 and 20% glycerol (that were obtained from duplicated samples) are shown in Fig. 2. This figure displays that the paths of drying-wetting for different flooding fluids are nearly S-shaped curves. It is also seen in this figure that the order of the curves in this space is dependent on the percent of glycerol, the curves for the sample flooded with distilled water and 20% glycerol are located at the top and bottom of the space of void ratio against water content.
Figure 2. Water content-void ratio paths for different quality of flooding fluids
The change in the thickness of the diffuse double layer (DDL) affects on the swelling behavior of soil. The thickness of DDL is dependent on factors such as valency and concentration of cations, temperature, and dielectric constant. The value of dielectric constant for water is 80 and for solutions of 10 and 20% glycerol are 74.9 and 71.8, respectively. The magnitude of the attractive and repulsive forces between clay particles are inversely and directly depended on the value of the dielectric constant. The reduction in the value of the dielectric constant causes an increase in the attractive forces and leads to a reduction in the thickness of DDL. When the flooding fluid is a solution of glycerol, the initial chemical composition of pore fluid in the sample is changed. The chemical composition of pore fluid has different effects on the structure of clay soil such as changes in the thickness of DDL. When the flooding fluid is distilled water the pore fluid of samples has a dielectric constant of about 80. Therefore, the values of attractive and repulsive forces are not changed because of the same dielectric constant of flooding fluid and pore fluid. The results of tests on these samples (flooded with distilled water) show that by repeating the wetting and drying cycles the potential of swelling is reduced and after several cycles a reversible equilibrium condition is attained as depicted in Fig.1. When the pore fluid is the solution of glycerol, the attractive forces are increased due to the reduction of the dielectric constant of pore fluid and causes a reduction in the thickness of DDL. The shrinking of DDL is led to the formation of flocculated structure in the soil and results in pasting of particles together leading to the reduction potential of swelling. When the concentration solution of glycerol is increased the dielectric constant is decreased, the magnitude of attractive forces is increased and the degree of flocculation of the soil structure is increased that is yielded to a reduction of swelling potential.
Conclusion
Effect of different flooding fluids on the properties of an expansive soil during wetting and drying cycles were studied. The following conclusions can be drawn from the present research:
-After a number of wetting and drying cycles, the observed irreversible deformation was diminished and equilibrium was achieved. The solution of glycerol causes more reduction in the potential of swelling than distilled water.
-The wetting and drying paths in the space of void ratio and water content are S-shaped curves. The variations in the void ratio of samples flooded with the solution of glycerol are smaller than distilled water.
./files/site1/files/142/babaei.pdf
Mohammadkazem Amiri, Gholam Reza Lashkaripur, Siavash Ghabezloo, Naser Hafezimoghadas, Mojtaba Heidaritajri,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
CO
2 injection in deep geological formations, such as depleted oil and gas reservoirs, in addition to the environmental benefits, is one of the effective method for enhanced oil recovery (EOR) as tertiary EOR. Presence of reservoirs with a pressure drop which require injection of gas in the southwest of Iran and having the technical and environmental effects of CO
2 injection have created a huge potential for CO
2 injection to EOR in this region
. In the first step, to perform CO
2-EOR, the geomechanical assessment is needed to find out pore pressure, in-situ stress magnitudes and orientations and fractures and faults conditions. In this paper, the initial in-situ pore pressure is predicted using modified Eaton method for 47 wells in the length of the study field and calibrated using repeat formation test and mud pressure data. In-situ stress was obtained by the poroelastic method for 47 wells in the length of the study field and calibrated using leak off test and extended leak off test. Then, the orientation of in-situ stresses is obtained based on image logs. Hydraulical and mechanical activities of fractures and faults were performed by critically-stressed-fault hypothesis
Material and Methods
In this paper, the initial pore pressure is calculated using modified Eaton method and other corrections that are proposed by Azadpour et al. (2015). The estimated initial pore pressure is validated using mud weight pressure (Pmw) and
repeat formation tester (RFT) data. In-situ stresses are composed of three orthogonal principal stresses, vertical stress (S
V), maximum horizontal stress (S
H), and minimum horizontal stress (S
h) with specific magnitude and orientations. The magnitude of S
V is calculated by integration of rock densities from the surface to the depth of interest. The poroelastic horizontal strain model is used to determine the magnitudes of the S
H and S
h. Then, the estimated minimum horizontal stress from poroelastic horizontal strain model is validated against direct measurements of LOT and XLOT tests. The orientation of breakouts was determined based on compressively stressed zones observed in the UBI log and using Caliper and Bit Size (BS) logs. The hole elongates perpendicular to the S
H and breakouts develop at the azimuth of S
h. Fractures and faults reactivation analyses are very important, they can potentially propagate upwards into the lower caprock and further through the upper caprock due to CO
2 injection. Fractures and faults identification were performed based on image logs. Based on performed seismic interpretations by NISOC (National Iranian South Oil Company), 15 faults have been detected in the field. Fractures and faults conductivity and activity in the current stress filed affect on fluid flow and mechanical stability or instability of the CO
2 injection site. Critically stressed fault hypothesis, introduced by Barton et al. (1995), states that in a formation with fractures and faults at different angles to the current stress field, the conductivity of fluids through their apertures are controlled by the interplay of principal stress orientations and fracture or fault directions. Hence, conductive and critically stressed fractures and faults in the current stress field were evaluated using critically stressed fault hypothesis. Fractures and faults are plotted in normalized 3D Mohr diagrams (normalized by the vertical stress), therefore conductive and critically stressed fractures and faults were determined.
Results and discussions
The maximum distribution of initial pore pressure was 20-25 MPa in the field and the average of initial pore pressure was 25 MPa in the field. Unlike the World Stress Map, the stress regime is normal in the reservoir. Because the Kazeroon fault and Dezful Embayment act as a strike-slip tensional basin, resulting in the subsidence of Dezful compared with other regions. The frequency distribution of calculated in-situ stress in 47 studied wells in the length of the field has been presented. The maximum frequency distribution of S
V, S
H and S
h were between 60-70, 50-60 and 30-40 MPa, respectively. A large amount of fracturing is observed in 20-25 m below the caprock. Based on the continuity of their low amplitude traces on the acoustic amplitude image of UBI, fractures are classified into 4 classes: discontinuous-open, continuous-open, possible-open and closed fractures. OBMI and UBI image logs processing were performed in 7 wells. As can be seen from the image log, and caliper analysis the most dominant strike of S
H around the well is 27
◦ and S
h strike is 117◦. These have two dominant orientation, some faults are along the strike of the Zagros fold-thrust belt (NW-SE) and the others are perpendicular to the Zagros fold-thrust belt strike (NE-SW).
Based on the normalized 3D Mohr diagrams it is clear that the fractures and faults that are oriented to the S
H will be the most permeable, because the faults and fractures experience the least amount of stresses in the direction of S
H and they have minimum resistance to flow in this direction, therefore will have relatively high permeability. Also, results showed the faults number 15, 6, 10 and 2 will be the most dangerous faults during CO
2 injection.
Mehdi Zare, Ali Moradzadeh, Abolghasem Kamkar-Rouhani, Faramarz Doulati-Ardejani,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
"Sulfide-carbonate" deposit is a term, which comprises a series of sulfide minerals such as Zn-Pb ore minerals, mainly considered as related to weathering of Zn-Pb sulfide concentrations and influence in sedimentary hosts (carbonate). There are more than 350 Zn-Pb deposits located in Iran, including world-class deposits such as Angouran, Mehdiabad and Irankouh. Due to the mining activity of these deposits, it creates a significant amount of mine waste that releases
of these wastes in the environment causing severe problems. One of the main problems is the formation of Acid Mine Drainage (AMD). AMD is produced by oxidation of sulphide minerals, particularly pyrite (FeS2) in waste dump. Due to low pH and the ability to dissolve metals and other compounds, it can host a number of environmental problems. A phenomenon known as natural or alkaline mine drainage (NAMD) occurs at high pH values when the neutralizing minerals are significantly present in the mine waste or when the oxidation of the sulfide minerals is poor. However, the metals and cationic species, such as Cu, Pb and Cd, are more soluble at low pH. In contrast, elements that form anionic species, such as Se, Cr, V, and Mo, tend to be more soluble at high pH and Ni, Zn, Co, As, and Sb, are soluble at near-neutral pH, and can potentially contaminate mine effluents, even without acidic conditions. Therefore Acid or Neutralization potential
(AP&NP) of waste dump
is significantly affects on the composition, transfers and fates of contaminati
ons transmitted from waste dump. The aim of this study was to monitoring heavy metals concentrations and assessments of pollution potential of waste dumps in Anguran mine by static method and has been compared by mineralogical approach.
Material and methods
The Angouran Zn-Pb deposit is located in the 135 kilometers southwest part of Zanjan Province, NW Iran. This area belongs to the northwestern part of the Sanandaj-Sirjan Zone, a metamorphic belt related to the Zagros orogeny. Angouran mine is one of the most important carbonate hosted Zn-Pb deposits in Iran that mining activity has been created a significant amount of waste dump in around pit. To achieve the goals, the 47 samples taken from different surficial parts of the waste dump were analyzed by using the ICP-MS method to determine the concentration of elements and heavy metals. These elements and metals includes: Ca, Mg, S and As, Cd, Cr, Cu, Ni, Pb, Zn. The pollution index (PI) were modeled for heavy metal contamination risk zoning then modified Acid Base Accounting (ABA) static method was used to evaluate of acid and neutralization potential (AP&NP) of the waste dump samples and the results were modeled by Kriging method. At the end, mineralogical approach (Mg + Ca concentration) was used to determine the source of neutralization and to better interpret the static results.
Results and discussion
The results of contamination index showed that zinc, arsenic and cadmium had the highest average contamination index (18.89, 12.13 and 5.8, respectively) and the trend of total metal changes in the region as Zn> As> Cd> Pb > Ni> Cr> Cu was rated.
Datas measured in modified ABA method were modeled in 2D maps using the Kiriging method. Due to the low total sulfur content (less than 1%), all of the samples were Net Neutralization Potential (NNP) with a range of 49- 990 kg calcium carbonate per ton, and the study area was classified into three neutralization potential (NP), High (NP) and Very High (NP) levels. The mineralogical approach (Mg + Ca concentration) was used as a useful tool for better interpretation of modified ABA results and determines the neutralizing source. Mineralogical approach results indicate that calcite species are the main source of neutralization and have high correlation coefficient (R = 0.99) with the modified ABA method. In order to validate the results, the presence of mineral calcite was confirmed by XRD analysis on 4 samples.
Assessment of AP and NP of sulfide – carbonate waste dump in this research can be used as a basis model for other similar mines to control environmental problems and to identify the behavior and to transfer heavy metals in mine drainage in the future. Mineralogical approach results show that neutralizing potential and neutralizing source can be obtained without using expensive mineralogy analyses in this type of carbonate-sulfide deposit
Rasool Yazarloo, Amin Jamshidi, Seyed Abdolghader Amanzadeh, Abuzar Esfandyaripur,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Loess soil is one of the problematic soils that should be improved its geotechnical properties before the project is implemented. Lack of attention to this issue has caused in many problems for civil projects in Golestan province. This has been more evident in some of the rural areas built on this type of soil. Moreover there are many reports regarding different geological hazard such as subsidence, divergence, erosion and landslide in Golestan loess soil. Among the different types of loess soils found in Golestan province, silty loess should be given more attention due to their large extent and being the bed soil of many villages, and many reports of its hazards.
One of the methods for improving soil mechanical behavior and its geotechnical properties is to use additives to reduce geological hazards. Due to the fine-grained structure of loess soils, the application of nanoparticles is more efficient and could result in solving many of the related problems. Nanotechnology is new scientific field which affects many aspects of engineering and in recent years, many efforts have been made to use this new technology in various geotechnical branches.
So far, research has been carried out on the improvement of various soil types with additives such as cement, bitumen, ash, lime and various types of nanoparticles. Nowadays, the use of nanoparticle additives due to reduction of environmental pollution than other additives has a wider application in improving the physical and chemical properties of problematic soils.
In the present study, the effect of nano-kaolinite on strength properties including uniaxial compressive strength, elasticity modulus, cohesion, and internal friction angle of silty Loess in Kalaleh city of Golestan province have been investigated.
Material and methods
In order to carry out the present research, sample of the silty loess soil from Kaleh city of Golestan province was collected and prepared. Then, 0.5, 1, 1.5, 2, 3 and 4 weight percent of nano-kaolinite were added to soil samples. The soil samples were prepared in a natural state (without additives) and with the additive for uniaxial compressive strength and direct shear tests. Strength properties of soil specimens including uniaxial compressive strength, elastic modulus (based on uniaxial compressive strength test), cohesion and internal friction angle (based on direct shear testing) were determined for native soil and its mixture with different percentage of nano-kaolinite. The data were analyzed and the effect of nano-kaolinite on the strength properties of the silty loess soil sample was investigated.
Results and discussion
Uniaxial compressive strength and modulus of elasticity have been increased with increasing amount of nano-kaolinite, and after 2% nano-kaolinite, increase in nano-kaolinite did not have any significant effect on uniaxial compressive strength and modulus of elasticity. The uniaxial compressive strength and the modulus of soil elasticity in the natural state (without nano-kaolinite) are 1.12 and 15.89 kg/cm
2 respectively, and when 2% of the nano-kaolinite is added to the soil, the values of these properties are maximal and reached to 1.19 and 18.10 kg/cm
2, respectively.
For native soil (without nano-kaolinite), the cohesion value is equal to 0.09 kg/cm
2, and with increasing nano-kaolinite from 0.5 to 2%, the cohesion shows an incremental trend and reached to 0.16 kg/cm
2. With increasing the additive percent from 2 to 4% the amount of cohesion were constant and equal to 0.16 kg/cm
2. The increasing of cohesion can be attributed to the fact that nanoparticles enhanced water absorption of soil particles which caused in better cohesion and also they affected chemical actions and surface electrical charge of soil particles.
Conclusion
The results of the uniaxial compressive strength tests show that adding up to 2 weight percent Nano-kaolinite to the dry soil increases the uniaxial compressive strength and modulus of elasticity of sil
ty loess soil in the Golestan province, which can be due to proper locking between the nanoparticles and soil particles and increased cohesion.
The results of direct shear tests showed that adding up to 2% nano-kaolinite to dry soil increased the cohesion of the soil and consequently increased the shear strength of the soil.
On the other hand, adding the different amount of nano-kaolinite has not changed much in the internal friction angle of the silty loess soil in the Golestan province.
Hojjat Ollah Safari, Hamed Rezaei, Afsaneh Ghojoghi,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
The landslides, as a natural hazard, caused to numerous damages in residential area and financial loss. In many cases, we can forecast the occurrence probability of this natural phenomenon with using of detail geological and Geomorphological studies. This seems that one of the most effective parameters in landsliding phenomenon is structural parameters, especially faulting in rocky outcrops. For verifying this hypothesis, the Nargeschal area, as high potential of hazardous area, is selected as case study for investigation on influences of faulting on landslide occurrence probability. Many large composite landslides were happened in 2016 and hence, this area is enumerated an active zone of landsliding. This area with geographic attitude 55° 09' 06" to 55° 27' 21" Eastern Longitude and 36° 54' 23" to 37° 05' 15" Northern Latitude located in south of Azad shahr (in Golestan Provinces) placed in Northeastern of Iran.
Geological studies indicate that this area located in northern limb of Alborz fold belt (as a young fold-thrust belt with 900 km length) which formed in late Alpine orogenic events by convergence Afro-Arabian and Eurasian plates. In this zone, the structures have main NE-SW trends with main active faults such as Khazar and North Alborz faults, as reverse faults with north-ward movements. The remnant part of Paleotethyan rocks (which transported from collision zone toward southern part by low angle thrusts) located between these faults and formed the mountain-plain boundary hills.
Material and Methods
In this research, we investigated on effective parameters in landslide occurrence probability of Nargeschal area with using of remote sensing techniques, GIS environment abilities and complementary field investigations. Therefore, we have prepared the seven data layers of geological and morphological effective parameters which are affected on landslide probabilities. These data layers consist of: lithology of outcropped rocks, faulting condition, topographic slopes categorizes cultivation circumstances, seismicity condition, spring population (ground water condition) and surveyed occurred landslides. Then, the content of each data layer is weighted and classified into five classes in GIS environment. Finally, the content of each pixels in all of 7 layers are algebraically summed and recorded as an attributed table. Hence, the landslide hazard zonation map was prepared by drawing the isopotential surface map on the basis of quantities of attributed table by using of GIS functions in Arc view 3.2 software.
Results and Discussion
The results of this research illustrate that a high risk zone is located in central part of area as an oblique broad-stripe zone with NE-SW trend [6]. This zone is correlatable with high density of fractures zone and high population of springs and earthquake focus and also, taken place in Shemshak formation with shale, marl and siltstone rocky outcrops (upper Triassic- Jurassic in age).
Also, the results of investigations on influences of structural parameters (especially faulting) in landslide hazard demonstrated that faults are indirectly impressed on this hazard probabilities via formed the high slope topography, poor strength faulted rocks, locating of spring presences and creation of seismicity, and hence, defined the spatial pattern of landslides.
Conclusion
Nargeschal area in Northern limb of Eastern Alborz is selected as case study for investigation on temporal relationship between Faulting and Landslides. The following conclusions were drawn from this research.
- It seems that the fault surface plays the role of rupture planes for landsliding.
- The structural factors also increased the ground slope and then, the close relationship is formed between landslides and faults.
- The results demonstrate the genetically relationships between landslides and faults in macroscopic scale in Nargeschal area.
Hadi Fattahi, Younes Afshari,
Volume 14, Issue 3 (11-2020)
Abstract
Introduction
Drill-bit selection is one of the most important aspects of well planning due to the bearing it can have on the overall cost of the well. Bit selection in conventional and slightly inclined wells is a very delicate and complex process. In high angle and horizontal wells it is even more difficult. Historically, drilling engineers have selected bits on the basis of what has been worked well in the area and what has been determined to have the lowest cost run from offset bit records. Often the best bit records were not available for evaluation, because the best bit may not yet have been run, may have been run by a competitor or the engineer was new to the area. As a result the bit program was generally developed by trial and error and at significant additional costs for a large number of wells. In most cases the optimum program was never reached because there was nothing to predict that a bit selection change could further reduce the cost of the well. In this study, an alternative solution approaches using the concept of the power of data mining algorithms to solve the optimum bit program for a given field is proposed.
Material and methods
It has been considered an offset well to be drilled outside the known boundaries of a known field. For this purpose, the seventh well (X-7) of the same field was used as a verification point. The data was trained using the well log and rock bit data of six wells located in the field and the real well log data of well 7 was input as unknown data. These depths are selected based on reported rock bit program. When compared to the real data, it could be observed that the models (adaptive neuro fuzzy inference system, K-nearest neighbors, decision tree, Bayesian classification theory and association rules) estimates the formation hardness accurately. This minor discrepancy was also present with the company’s suggested rock bit program, which was based on the previous wells’ rock bit data.
Results and discussion
In this paper, data mining algorithms for optimum rock bit program estimation is proposed. The accuracy and efficiency of the developed data mining algorithms (adaptive neuro fuzzy inference system, K-nearest neighbors, decision tree, Bayesian classification theory and association rules) that requires sonic and neutron log data input was tested for several real and synthetic cases. In the case of a development? well to be drilled outside the known boundaries of a field the model estimated rock bits with properties that consider the formation hardness correctly but slightly underestimated further rock bit details. The models also produced reasonable rock bit programs for an advance well to be drilled within the known boundaries of a field and a wildcat well drilled in a nearby field with similar rock properties to the training field. Thus it was concluded that the developed adaptive neuro fuzzy inference system is suitable as a front-end system for rock bit selection that could help engineers in decision-making analysis.
Conclusion
Optimum bit selection is one of the important issues in drilling engineering. Usually, optimum bit selection is determined by the lowest cost per foot and is a function of bit cost and performance as well as penetration rate. Conventional optimum rock bit selection program involves development of computer programs created from mathematical models along with information from previously drilled wells in the same area. Based on the data gathered on a daily basis for each well drilled, the optimum drilling program may be modified and revised as unexpected problems arose. The approaches in this study uses the power of data mining algorithms to solve the optimum bit selection problem. In order to achieve this goal, adaptive neuro fuzzy inference system, K-nearest neighbors, decision tree, Bayesian classification theory and association rules were developed by training the models using real rock bit data for several wells in a carbonated field. The training of the basic models involved use of both gamma ray and sonic log data. After that the models were tested using various drilling scenarios in different lithologic units. It was observed that the adaptive neuro fuzzy inference system model has provided satisfactory results.
Ali Saket, Seyed Mahmud Fatemi Aghda, Ahmad Fahimifar, Hossein Sadeghi,
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
Analysis of time, location and magnitude of foreshocks and aftershocks has been one of the most important cases for experts in various scientific fields such as: seismology, structural engineering and crisis management, and other interrelated fields. Since this analysis and the result of studies on seismotectonic and cases of earthquakes help us identify the foreshocks and aftershocks with the goal of decreasing losses and nervious stress of the injured community in quake-stricken areas and skilled crisis management. The cause fault of earthquake plays the important role in foreshocks and aftershocks of the earthquake. So, study on fault behaviour is a suitable method for analyzing and routing the basic parameters of foreshocks and aftershocks. Also, foreshocks and aftershock are important parts of any earthquake in a seismic area. The analysis of the basic parameters of the foreshocks is one of the most practical researches for reducing the risk of earthquakes. The identification of behavioral pattern of foreshocks can help researchers detect the active fault conditions for the occurrence of earthquakes in different areas. The present study is concerned with the study of behavioral patterns earthquakes, foreshocks, and aftershock of
Zohan earthquake. Experience of large aftershocks in different parts of the world indicates that, following earthquakes and depending on seismic-tectonic conditions, large aftershocks are likely to occur in the earthquake-effected zone, which will aggravate the damage caused by earthquakes (Omi et al., 2013). The main factor contributing to the worsening of damage caused by aftershocks is the performance of structures that are weakened but not destroyed by main earthquakes and are, thus, highly likely to be destroyed by large aftershocks (Saket and Fatemi Aghda, 2006).
Material and methods
The present paper makes use of data collected in a real earthquake and similar expriences in other earthquakes for presenting a practical pattern for predicting primary earthquake patterns, determining the location, magnitude, and time of aftershocks. The target of this case is decreasing the effects of earthquake. To this end, we used the results from studies on basic parameters of foreshocks and aftershocks of Zohan earthquake, and 2012 earthquake in South Khorasan province. The rationale for selecting the aforementioned studies is: location of event, the Zohan earthquake, had been identificated as an area with high risk for the occurrence of earthquakes, although there has been no wide-scale earthquake in this area in the last two decades. These conditions are important causes for more concentrated studies on this area because there is a high chance for wide-scale earthquakes striking this area.
Result and Discussion
In this part of research, we conduct a study on the location, magnitude and depth of foeshocks. Some of the world-wide research suggested that these data can help to predict the time of mainshocks. Studies conducted on the variations of frequency in foreshocks can follow this goal.
In this paper, the available statistical data such as periodical variations of seismicity in the weeks leading up to the main shock can be used as a tool for estimating the approximate time of a future important earthquake. The weekly variations of seismicity before Zohan earthquake indicate a relative increase and then decrease within a 100 km radius around the epicenter of the main shock.
Table 1: Variations of frequency of foreshock based magnitude before Zohan earthquake
Week before main shock |
Frequency of foreshock in the Radius of 100Km from main shock |
Frequency of foreshock(with M>2.5) in the Radius of 100Km from main shock |
6 |
0 |
0 |
5 |
1 |
1 |
4 |
1 |
0 |
3 |
2 |
0 |
2 |
5 |
3 |
1 |
2 |
0 |
Studies on numerous earthquakes in Iran and other regions in the world show that the distribution of aftershocks can be related to fault type or the direction of principal stress (Saket and Fatemi Aghda, 2006) and (King et al., 1994). Whereas maximum Coulomb stress change is related to maximum principal stress in earthquakes, the concentration of aftershocks can coincide with the direction of maximum principal stress (σ
1) of the causative fault in mainshock. Considering the direction of maximum principal stress and its adaptation to the scattering of aftershocks, the above hypothesis is confirmed.
Also studies on frequency changes and seismic quiescence of small aftershocks help us in predicting future aftershocks. The results the of presented research by Itawa (2008) on the World earthquake catalogue suggest that seismic quiescence theory is true for different regions of the world. Based on the results of the study mentioned above, this case can be used as a tool for predicting large aftershocks in Zohan earthquake.
Fig 1. Adaptation of direction of maximum principal stress with scatering of the aftershocks of Zohan earthquake. a: direction of maximum principal stress (σ1) of the causative fault in mainshock. b- scaterring of the aftershocks
Table 2: Seismic sequience versus magnitude of aftershocks
Row |
Seismic Quiescence for aftershocks |
Aftershock Magnitude |
Data and Time of aftershocks |
1 |
13 |
3.0 |
2012/12/05
17:21:03 |
2 |
36 |
3.4 |
2012/12/05
17:57:03 |
3 |
161 |
3.1 |
2012/12/05
20:38:09 |
4 |
3906 |
3.9 |
2012/12/08
13:44:19 |
In addation, frequency of aftershocks and certain time distance (seismic quiescence) between their can use precursors for detecting the time of large aftershocks. The relevant analysis in this study showed that methods such as: time series beside seismic quiescence can help in conducting a more accurate time forecast of large aftershocks.
Conclusion
- The results of this research suggest that we can identify some of the charactristics of the main shock by focusing on location, magnitude and depth of foeshocks.
- In Zohan earthquake, the direction of maximum principal stress is adpated to the scattering of aftershocks, and this case suggests that there is a specific relationship between them.
- The relevant analysis in this study showed that the methods such as: time series beside seismic quiescence can help conduct a more accurate time forecast of large aftershocks../files/site1/files/144/saket.pdf
Tayebeh Mirjalili, Mashala Khamechian, Mohammadreza Nikudel,
Volume 14, Issue 4 (12-2020)
Abstract
Abstract
This study aimed at evaluating the effect of calcic aggregates of engineering geological properties on the artificial stones properties, non-resin cemented and then, to make a comparison between the engineering properties of artificial and natural stones. To investigate the effect of calcic aggregates properties on artificial stones, seven samples of building stones including black limestone, three samples of marble (Chinese stone, marble and crystalline marble) and two samples of travertine and onix were used. Engineering geological properties of the samples were then determined. In the next stage, after designing mould for constructing artificial stones, aggregates with the same grading and mixture design were provided. Then two samples including coarse and fine grained artificial stones were made for all of the mentioned aggregates under the same vibration, pressure and vacuum conditions. Next physical, strength and durability tests were conducted, and the obtained results were compared. The results of engineering parameters showed that Hojjat Abad travertine artificial stones have similar engineering quality to own natural stone and Crystaline Marble and Turan Posht travertine artificial rocks have about 11 to 32% increase in quality but Chinese stone, Black limestone, onix and marble have a 6 to 33% lower quality than own natural stone. However, the samples made of other stones in view of the compared parameters related to artificial stones have lower quality than natural stones; however, they are placed in the acceptable range as building materials.
Introduction
Given the variation of construction materials, the importance of the economy in its supply and large use of natural stone mines and the production of seemingly unusable slags, it is necessary to reuse these slags. One of these reusing methods is to make artificial stones and its application as construction materials. Rock powder, aggregate, a small amount of cement or resin and other chemicals are used for producing artificial stone. In this study, carbonate minerals, rock powder and white cement in the first phase are mixed and wet. Then, in the next stage, to form the sample in a cubic mold, they have been compacted under three physical processes of vibration, vacuum and pressure. The aim of this study is to investigate how to make artificial stone, to evaluate the engineering properties of artificial rock and the effect of limestone engineering properties on artificial stone properties of non -resin cement and then comparing the properties of artificial rocks made with natural stones
Material and methods
In this study, in order to investigate the effect of calcic aggregates properties on artificial stone properties, seven samples of building carbonate rocks including crystalline marble, two samples of marble, black limestone, and two samples of travertine and onix were used.
Engineering geological properties of the used samples were then determined. In the next stage, after designing mold for constructing artificial stones, aggregates with the same grading and mixture design were provided. Then two samples including coarse and fine grained artificial stones were made for all of the mentioned aggregates under the same vibration, pressure and vacuum conditions. After construction, physical, strength and durability tests were conducted, and then the results were compared.
Results and discussion
Investigation of the effect of engineering geological properties of carbonate aggregate on artificial stone properties showed that the artificial stones made of travertine aggregates have higher quality than natural travertine in terms of physical, strength and durability properties. Due to the existence of pores on the surface of travertine aggregates, the used cement can result in reducing effective porosity and increasing strength and durability in the artificial stones.
In Table 1 a proposed research has been used for rating rock engineering parameters based on the degree of importance for building stones. Then, according to this table, the score of each natural stone and related artificial stones were determined. For building stones, the importance of durability and strength is more than the density. Also, the density shows its effect on durability. At the same time, with increasing the percentage of water absorption, the durability of rock has decreased. Therefore, the rocks with less water absorption are more important.
Table 1. Scoring of building stones based on the engineering parameters
Parameters |
Description |
Excellent |
Good |
Marginal |
Poor |
Total score |
100 |
75 |
50 |
25 |
Water absorption (%) |
Range |
0-2 |
2-3 |
3-5 |
>5 |
Score |
25 |
20 |
15 |
10 |
Unit weight (kN/m3) |
Range |
>24 |
22-24 |
18-22 |
<18 |
Score |
15 |
10 |
5 |
3 |
Uniaxial compressive strength (MPa) |
Range |
>50 |
40-50 |
30-40 |
<30 |
Score |
20 |
15 |
10 |
4 |
Tensile strength (MPa) |
Range |
>20 |
15-20 |
10-15 |
<10 |
Score |
20 |
15 |
10 |
4 |
Durability (%) |
Range |
<1% |
1%-2% |
2%-3% |
>3% |
Score |
20 |
15 |
10 |
4 |
The total score of fine
-grained artificial stones (65%) is almost similar, indicating that the type of carbonate grains does not affect the characteristics of fine
-grained artificial stones, but the total score of coarse artificial grains are in the range of 58 to 74%
. This range of score indicates that structural weakness, especially the cleavage surface, porosity, lamination, vein and acetylolite of aggregates have more influence on engineering properties in coarse-grained artificial rock
.
Conclusion
Comparison between the engineering properties of artificial and natural stones were studied. The following conclusions were drawn:
- The artificial stones of Hojjatabad travertine have similar engineering quality with their natural stone.
- Both Crystaline marble and Turan Posht travertine artificial rocks have about 11 to 32% increase in quality but Chinese stone, black limestone, onix and marble have 6 to 33% decrease in quality compared to natural stone but in acceptable ranges when they are considered as construction materials.
- The samples made of other rock samples have lower quality than natural stones; however, they are placed in the acceptable range as building materials.
./files/site1/files/144/Mirjalili.pdf
Vahid Shirgholami, Mahdi Khodaparat, Abolghasem Moezi,
Volume 14, Issue 4 (12-2020)
Abstract
Introduction
Excavation in urban areas occasionally is accompanied by the improper performance of the support system for even small deformations. In this regard, deformation control design based on force-based approaches provides a more realistic reprehensive of excavation performance. Top-down deep excavation techniques are among the modern excavation stabilization methods in urban areas. In this method, unlike the conventional methods, it is possible to perform the excavation and construction operations simultaneously. The present study aims to investigate excavation stabilization using the main structure through the top-down approach. For this purpose, field and numerical evaluations of the stabilized project were conducted based on the top-down approach in the downtown of Qom city, Iran. This research reports the information obtained through monitoring and modeling using the finite element ABAQUS software, predicting the occurred deformations until the end of excavation operations using the calibrated model, and offering an initial estimation of the required stiffness for the support system with respect to the lateral deformations in four sites proposed, according to the studies of Line A Qom Subway.
Project specifications
Based on the geological studies of Line A Qom Subway Tunnel, the geological layers are classified into four soil classes. Qc-1 consists of gravely sand with fine content of 5 to 20%; Qc-2 is silty and clayey sand with fine content of 35 to 60%; Qf-1 is clayey silt with fine content of 60%; and Qf-2 is a silty clay layer with fine content above 60%. Line A of Qom subway passes the study area of the present study, which is located in Ammar e Yaser Street (Station A6). Based on the geotechnical studies of the project site, the site in the levels near the ground consists of Qc-2 but in the lower elevations, it is composed of Qc-1 and Qf-2.
Salam Trade Complex, located in the downtown of Qom city, has 6 underground stories and 6 above-ground stories. It is limited to the main street in the south and to urban decay in the three other directions. The final excavation depth, length, and width is -21, 36, and 32-52 m, respectively. The project structure consists of a steel moment frame with a retaining wall in the negative elevations and metal deck frame for ceiling construction. In this project, excavation wall deformation was monitored in three important sections (A, B, and C). Due to the vicinity to urban decay, a total station TS02 was used for monitoring these sections. According to the field surveys, the maximum horizontal deformation of the walls in sections A, B, and C is 24.10, 42.16, and 47.21 mm, respectively, which were measured in the 0, -1.5, and 0 m elevations.
Monitoring process and numerical simulation
To calibrate the prepared model, a sensitivity analysis was performed on geotechnical parameters including modulus of elasticity (E), internal friction angle (φ), and cohesion (C) of the layers by simulating 60 numerical models. Based on the sensitivity analysis results, an increase in internal friction angle and elasticity modulus for layer 1 (i.e., φ1 and E1) and elasticity modulus of layer 3 (E3) results in a decrease in lateral deformation. Finally, using the sensitivity analysis results and after several trials and errors, the numerical models for sections B and C were calibrated when reaching the depths of -8 and -11 m, respectively. Using these models, then, it is possible to predict deformations up to the end of the project.
To determine the required stiffness for the excavation support system, regarding the acceptable deformation of the adjacent soil mass, 160 numerical models were built and their results were analyzed. Based on the results of Brason and Zapata (2012), relative stiffens (R) were used to develop a relationship between the maximum lateral deformation of the wall and the required stiffness of the support system. R is a dimensionless parameter that represents the stiffness of a solid support system; the greater this value is, the more flexible the system would be. In this study, caisson pile length, excavation width, and buried depth of the wall were used for determining the R.
R =
![](file:///C:Users1AppDataLocalTempmsohtmlclip11clip_image001.png)
(1)
Figure 2 presents the maximum occurred deformation in terms of depth versus the relative stiffness for sites QC and QF.
Figure 2. Maximum deformation in terms of depth versus the relative stiffness for sites QC and QF
Conclusion
- According to the monitory data, the maximum lateral deformation in sections B and C until the end of the project was 42.16 and 47.2 mm, respectively. Moreover, the deformation of the other points inside the excavation was 30 mm.
- Considering the occurrence of maximum lateral deformations in the higher elevations in the monitored sections, it is inferred that excavation support at the ground level plays a key role in this approach. Hence, the lack of completing the structural frames and slabs for facilitating the excavation operation can lead to an increase in deformation levels.
- Based on the prepared graphs, the top-down approach in sites QC-2 and QF-2, compared to sites QF-1 and QC-1, provides a more desirable performance for deformation control.
Ata Shakeri, Maryam Madadi,
Volume 14, Issue 5 (12-2020)
Abstract
We collected soil samples at 23 sites from the petroleum contaminated soils (PC) in the west of Kermanshah province to investigate the sources and ecological risk of polycyclic aromatic hydrocarbons (PAHs). In this study, source apportionment has been carried out using Positive Matrix Factorization (PMF).The total PAHs concentration, have a mean value of 92.79 mg/kg, ranging from 7.37 to 609.67 mg/kg in PC soil samples. The average abundance order of different PAH ring compounds are 3 rings > 5+6 rings > 4 rings> 2 rings. The ecological risk assessment of PAHs revealed that all of the PAHs levels were higher contents than the effects range low (ERL) value and show higher concentrations than the ERM values, except for Pyr, Chr, BaA, BbF, BkF and BaP in the soil samples. The result of benzo (a) pyrene equation (BaPeq) values indicates that the carcinogenic potency of PAHs should be given more attention due to the impending environmental risk in the study areas. Based on the PMF analysis four sources of PAHs are identified including coal combustion (21.48%), vehicular source (13.74%), unburned petroleum (20.84%) and creosotes (43.92%).Therefore, it was concluded that petroleum activities were major sources of PAHs in west of Kermanshah province.
Habib Shahnazari, Mahmoud Fatemiaghda, Hamid Reza Karami, Mehdi Talkhablou,
Volume 14, Issue 5 (12-2020)
Abstract
The present work is conducted to investigate the effect of texture and carbonate content on internal friction angle of carbonate soils. Carbonate soils are majorly found in the bed of shallow waters and also offshores in tropical regions. Recently there is a huge construction projects including oil and gas extraction platform and facilities, harbors, refineries, huge bridges and other big construction projects in many offshore and onshore areas around the world. One of these area is located on southern part of Iran. We collected soil samples from different parts of northern coasts of Persian Gulf, then the following experiments were performed, carbonate content, three-dimensional grain size, angularity, relative density & direct shear. The results showed that the average of internal friction angle of carbonate soil is higher respect to known silicate sands. This angle is affected by effective grain size, grain angularity, and calcium carbonate content. Based on the experimental results of this study, one of the results was that the internal friction angle of carbonate soils decreases as their effective size of soil aggregates increases.